Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hi All,
In ble_app_hrs example two function is defined for gpiote_init()
1)
static void gpiote_init(void)
{
APP_GPIOTE_INIT(APP_GPIOTE_MAX_USERS);
}
2)
static void...
Hi
I found there is bonding managing routine in SDK HRM and Proximity examples.
bond_manager_init();
It means in these two case, after pairing with BTLE host, the...
My question is regarding the PPI channel groups. The documentation is extremely limited and leaves many questions.
My goal is to generate 3 PWM signals from a timer with...
If i understand tasks are for outputs and events are for inputs.
Wanted to know relationship between channel and the pin numbers. do they hold the relationship like...
Hello,
I am really confused on how to get a custom BLE service up and running. I have read through nAN-36, and compared the suggestions in that document to the HRS example...
In nRF51 reference manual v2.1 section 18.1.1, it mentioned that the RTC must be able to
run while the 16 MHz system clock (SysClk) source is OFF. 2 questions :
Q1: Since...
Hello,
I'm trying to get the SDK examples working in Eclipse. I have followed all steps(except debugging part) in the nan-29, but i can only import the s110/ble_hrs example...
I am looking for the spacing in mils or mm between the two samtec connectors on the nrfGO board. I am making my board to interface with the PCA10005/PCA10004 and I would like...
Hi,
I'm new to nRF8001 SDK and Bluetooth and I hope my questions are not too stupid lol. So here it goes:
I'm using the Nordic nRF8001 SDK to implement a self-defined...
Hi All,
i would like to know in ble_app_hrs example gpiote_init() is called from main
and then again called in led_start for what purpose it used in 2 place.
can...
I see that we can specify the SPI frequency in bps, I was just wondering how fast the SCK line was oscillating for these values. Does it use the 32.768 kHz crystal oscillator...
If the nRF51 chip is in System Off state, do the GPIO pins retain the pull-ups or pull-downs? If so, what value do they have and how much current can they sink or source?...
Hi all,
when i want to connect different peripheral on central(s120).
it have a error and disconnect.
it seem ok , but that will disconnect later.
ant it get disconnected...
