Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I used the nRF51822 for my thesis and as I was looking for the url of the product spec I used I noticed something strange:
My product specification for the nRF51822 is version...
I've connected my nRF51822 mKit to my Linux system via a USB cable. While trying to upload code on the board, I got the following error:
SEGGER J-Link Commander V5.12g...
Currently i was using arduino for my development but now i want to move forward with Some SOC so i found nrf51822 IC.For using nrf51822 ic i need to buy another board which...
I would like to use the nRF24L01+ for a telemetry project that requires broadcast at 100% duty cycle at a fixed bitrate. Ideally, we could also use our own frame format. ...
I am trying to use whitelisting and a passkey to add security for my application. So far I have the passkey set up so that it is working on the master control panel on PC...
Dear sir.
From [nRF51_Series_Reference_manual], ADC maximum input voltage has two rules.
The ADC should not be exposed to higher voltage than 2.4 V on an AIN pin...
hi
i have one custom service that have 6 characteristics
when in android i want to write in one of characteristics it take about one sec .
is this for having 6 characteristic...
In the Androir master control panel app, in the scanner results there is a 'Type:' line for each device. Most of them around me say 'UNKNOWN' however some say 'BLE only'....
SDK 11.0.0, S132 v2.0.0, nRF52.
I have searched through the many questions already on the dev zone on this topic, but cannot solve my problem. I tried adding the dfu service...
hello all,
i am a begineer to nordic . i am trying to read adc PCF8591 value through TWI and i want to print the value in UART TERMINAL.
i have written the code. but...
Hi,
Im trying to connect ble_app_uart to my gsm module. For some reason program fails at runtime. I was expecting to find a filename and line number where the error has...
Hi,
nRF52 Board, S132. Now, I want 6 pwm, 6 adc .
nRF52 has 5Timers, Timer0-Timer4.
Now, I allocation these timers as follows:
//TIMER0 is used by softDevice
APP_PWM_INSTANCE...
Hi,
I want to access restricted peripheral: TIMER0.
After small research found that I should use sd_ wrappers, in my case sd_nvic_SetPendingIRQ(TIMER0_IRQn) however I...
Greetings,
I'm working with LPCOMP to detect a signal. This signal is the output of an opamp amplifier. What is happening is that when the LPCOMP is switched on there are...
Hi,
I am using SHT21 Temp sensor via TWI manager. As per the spec shown in the image
I have to add 20us delay between the sensor ACK and STOP command.
Is there any...
