This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi,
I have just bought NRF51822 without any extra peripherals(no motherboard/DK). Just plain Module like below image.
I am supplying 3.3V to VDD and also Connected GND...
Hi all,
I find a problem when testing the ANCS program. It seems that after you connect the device with ANCS with an iphone, you cannot connect the device with another iphone...
I built the ble_app_proximity project and down load into my board, it can advertise and can connected by the lightblue and the nRF toolbox, But i sent the hex value of 0x02...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
Hi,
I am currently working on a project with nRF52 preview DK.
In my system, an ECG chip is used to measure the heart rate and the data will be transferred back to nRF52...
Hi,
I have a number of products with nRF905 successfully deployed. Now, I am in a little struggle with a new one. The problem is the signal strength. The other products...
I'm trying to add a feature where my peripheral will temporarily trigger a Faster Connection Parameter for a period of time determined by an app_timer. However it seems that...
Hello Nordic Devzone.:
When studying the 8.0 BLE Central multilink example (s120 softdevice), I looked into the component relevant to button pressing interrupts, app_button...
How do I use the NRF51 or 52 to create a GATT server with read only service without requiring bonding? Basically I want to be able to provide more data than advertising allows...
I can not connect to one of my beacons, i need to reset its config, but HW way.
Can i reset it somehow?
It is nRF 51822 based, sensoro 4AA. I asked sensoro 3 days ago...
Hi Nordic guys,
we are using uart for communication with another MCU and flow control is used.
Beside the uart communication itself we have out of band signals (on gpio...
Dear Nordic.
I have used to nrf51822 custom device. I confused it because of Uart RX data.
The master device sends blow raw data to client device(nrf51822 custom device...
I'm trying to compile a program on mbed for a BLE Nano, which uses the nRF51822. I've included the nRF51822 library by Team Nordic that's listed on mbed's library wizard and...
Hello
i am trying to upgrade from sdk 9 to sdk 10 .zip version but after installing when i open some examples it asking me to install arm cmsis 4.5. pack and device family...
Hi can anyone guide me in configuring the peripherals of nrf51822 before putting the chip into sleep? For example, timer, i/o pins, etc... which is not needed to reduce the...
