For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I have a queston for softdevice S130 example about Environmental Sensing service.
I readed spec. but I can't find out any ESS profile example in SDK.
Is SoftDevice S130...
I want to use the nRF24LU1+ for a project where it will be a HID usb dongle. But I dont get which tools I need to make it. The KIT DEVELOPMENT NRF24LU1+ work for it?
T...
Hello,
This morning i did migration of my code from SDK 11 alpha 2 to 11 final on nRF52 and i have a big problem.
Nor bootloader or application do advertising. Am I...
I want to merge the softdevice and application in the makefile is it possible ?
if not possible what could be the easier way. I am using Linux OS .
thanks
Hi everyone.
I'm trying to program a NRF51822 Beacon using the nRF DK board. Of course I looked around here for advice on what type of connector to obtain.
devzone.nordicsemi...
Hi,
I have a hardware (wired) UART transmitting data to the nRF51 at intervals. I'm currently trying to implement UART-BLE that runs could concurrently with the wired UART...
is there a version of nrfutil that works on linux?
this one doesn't: github.com/.../pc-nrfutil
$ nrfutil dfu genpkg --application _build/nrf51822_xxac_s110.hex fota.zip...
Hello,
I have used ble_app_uart example and wants to transmit 12 bytes data over ble using this function ble_nus_string_send call.
In 1 second how many times ble_nus_string_send...
Hi,
At the moment I'm trying to make some current measurements with the new nrf52 dev-kit from the global tech tour. Unfortunately I'm not able to go into Idle- or even the...
Hi,currently i want to measure the current consumption of nrf52 DK. I followed the tutorial nRF51 current consumption guide ,and use the Power profiling application in the...
HI. currently, I have used the nrf52 board to test the power consumption of ble,I followed the tutorial nRF51 current consumption guide,loaded the Power profiling application...
I've got my UART (with fifo) functioning, and now I need to read in a string and determine whether to act upon it or not.
I'm using the s110 softdevice, and I found a BLE...
Hello,
i would like do Output over UART (printf) the UUID and the DeviceName.
I have the scanning data p_gap_evt->params.adv_report.data
When i would like to get...
I am using nRF52832 DK. I have connected our custom board using Debug out and loading code is successful for custom board. I loaded radio_test code.
Now I want to test the...
