I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
Hello All,
I am trying to build a BLE peripheral project with RTX OS which is using S110 Soft Device and bootloader is also there in Flash memory region. So when I am trying...
I am just beginning to develop with BLE.I came across the nRFgo Studio through Nordic and BDS through the bluetooth SIG.
1]What are similarities/differences between the...
Hi.
I want to active HW timer with SoftDevice 7.1.0 .
Timer operation is good but I can not stop the timer.
The power consumption is 200~300uA after timer expired ( or...
Hi,
We would like to use NRF52832 chipset for our project, and we need to configure 11 pins as GPIO interupt , Is this possible ? How many pins we can have as interrupt...
I have Bluetooth iOS app communication with my nRF51822. I notice that when I connect the the nRF, the first GATT write event is always the same:
p_ble_evt->evt.gatts_evt...
I am using SDK v11-alpha2 and following the BLE Services and BLE characteristics tutorial.
When calling sd_ble_uuid_vs_add as the Characteristics tutorial asks, I get a...
HI ,ALL ,
i have change the project for the purpose of enter a six digit key at cellphone side to enable the notification with the board(52382).
But when i input the...
Hello, I looked througth the devzone but didn't find direct answer. So created new one.
RM v3.0 states chapter 12.1.19 "Reset behavior" with table. However, it is not clear...
Hi,
I have to check every 10 minutes the battery level when BLE is connected .
I have found in this forum this source : github.com/.../main.c
As the source date is...
Hello All,
I developed one project in nRF51822 with S110 Soft Device based on following configuration.
SDKv10.0.0
DFU capable
RTX Support
And now I want...
Hi ,
I am using Soft Device S130 and NRF51 kit PCA10001. I am using SDK 11.0.0-2-alpha .
I am trying to test the Alert Notification Service Example as mentioned here...
Hello!
I'm trying to use the nRF51422 internal ADC to send the value over BLE then monitoring the value received on the nRF Master control panel on Android phone but I...
hi
I touched pca20001 mouse -> main.c
i followed this link to debugging
devzone.nordicsemi.com/.../
but i can't build this..
because it said "ERROR" over 40...
