Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I recently grabbed the latest SDK nRF5_SDK_11.0.0-2.alpha. I was looking at some of the changes and wanted to run one or two demos to make sure I was able to build them properly...
I am testing this on ble_app_hrs and ble_app_hrs_c. After devices are bound I would like to skip discovery as it takes long time. So all I need to do is get the service's...
After I receive data by ble_nuts,using example ble_app_uart.
I call ble_nus_string_send to the central, however I got error,I print error code is 8 which means "NRF_ERROR_INVALID_STATE...
hi
First,I apology for my poor English...
I want to make a project to connect 2 device.
With a sensor from TI , which comes out the sensed signal .
Transfer the data...
Hi,
platform info:
SDK 9.0, NRF51822, SD:s110_nrf51_8.0.0, Master Control Panel(android):2.0.0
We use eample dual_bank_ble_s110 under dfu/bootaloader/pca10028/ of SDK...
Hello,
I've built "bootloader" project in sdk6 and sdk8, which named "sdk6_bootloader.hex" and "sdk8_bootloader". Then what I did are listed as below:
(1)
using ...
I am trying DFU with:
BOARD_PCA10040,
nRF52_SDK_0.9.2_dbc28c9
s132_nrf52_1.0.0-3.alpha
One interesting thing is the SDK_0.9.2_dbc28c9 can not work with
...
Hi,
We currently (no pun intended!) don't have any battery protection circuitry for reverse polarity designed into our prototypes. Our device is powered from a CR2450 coin...
Dear Nordic.
I read specific data using GPIO(timer sampling), BUT, occasionally, the data is broken because of Softdevice interrupt.
So I want to guarantee it while reading...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Hello everyone.
I would like to ask if is possible to compile and run examples from latest IoT SDK 0.9.0 on pca10028 board. Every example has only Makefile for latest pca10041...
Dear Developer Zone,
I'm using an nrf51822 with SDK8 & SD S110 v8
We have an iOS app connecting to a custom service on the NRF device. What we would like to do control...
