Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hello
I've been experiencing an unusual problem using the TWI/I2C library for the nRF51-DK board. Basically, I found that I need to shift my device address to the left...
Hi guys,
I have followed devzone.nordicsemi.com/.../ to set up CrossWorks. Even though I got pass the ble_stack_init();, I still can't discover the device for some reasons...
Hi
Please tell me someone me how to start nRF51822 & softdevice8.0.0
I build a NRF51822 application in gcc & ECLIPSE.
When to run the program, it crashes in the boot...
I'm having a problem adding the GPIOTE_IRQhandler() to my main.c file (see attached). I'm getting a compiler error that it is doubly defined in app_gpiote.o and main.o, but...
is it possible to update the pca20006 (rev. 1.2.0 2015.06) beacon with the pca10000 over DFU?
When i tried to update it with my application written for an older version ...
Hi folks,
I'm using the ble_app_template on a custom board. The BSP has a bunch of stuff I don't need, so I would prefer to not use it and handle my I/O directly instead...
i was going through TWI initialization process here i am confused why have we disabled Blocking mode. The reason for Disabling TWI_BlOCKING_DISABLED
I am referring the below...
hi , i want to modify the "transmitter_pca10028" and "receiver_pca10028" examples in SDK to obtain a transmitter/receiver in the same time (tranceiver). So someone have idea...
Hello, I am using the nrf51822EK and I want to combine the ADC and LPCOMP although in the reference manual it says they can not be used at the same time. Is it possible to...
Hi all,
I met one strange thing on SPI interrupt:
when 51822 advertising, the SPI write and read works well;
But, when CONNECTED, with BLE_GAP_EVT_CONNECTED event occured...
Hello,
I migrated my project from softdevice S110 7.1.0 on a nRF51422 FAC to softdevice S110 8.0.0 and an nRF51822 FAA G3. My code used to have a current consumption around...
Hello everyone,
I'm currently using and modifying the experimental_ble_app_uart. I've seen that for sending characters resp commands the file simple_get_uart is used. My...
Good morning.
I'm curently trying to set up an exemple project in Eclipse, but I've tried sevrals tutorials unsuccessfully. Somes are out of date, somes gives me errors...
