Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi.
For my application, i want to do a battery saver profile.
I need to send one advertising package every 30second.
So now i do this by setting
#define ADV_TIMEOUT_IN_SECONDS...
Hello,
we have an application that involves 3 devices that comunicate over ANT. One central device beeing slave to the two other devices. All channels are configured with...
In ble_gap.h I noticed a parameter called BLE_GAP_ADV_INTERVAL_MIN, which determines the minimum gap between BLE advertisements. Current setting is 0x0020.
Currently in...
AN36 refers to the Send Update button on Master Control Panel(to toggle the LED). I can only see a "Write" and "Write Long". Am I doing something wrong, or does AN36 refer...
This may be the most commonly asked question but I'm new to this embedded devices.
I'm trying to develop a nRF51422 based sensor network which operates using CR2032 battery...
Is there a firmware I can download to have nRF51 Dongle working with ANTWARE II?
I plugged in nRF51 Dongle (PCA10031 V1.0.0 2014.30). I can see it in nRF Studio.
When...
Dear Sir,
I'm studying S120 and S130 soft device.
However, the document inside SDK dose not explain the detail of connection procedure.
I'm interest in the device how to...
I have one task to send image to nordic device(BLE device), But i am confuse to where to start,
Is it Possible to send image to Nordic device Using BLE?
Any guidance on...
Hi! I've never worked with bluetooth before. I am using a Blend micro arduino-based board to send to the computer some different values (for instance an array of 10 float...
Hi,
I have a question related to GATT Services in BLE, so not strictly a nrf51 question although it's related to one of the examples. The example for the (Human) Thermometer...
I have a BLE wearable (Pebble watch) that I wish to detect using the nrf51822 evaluation kit. I can use the Control Panel to see the pebble. I would like to be able to us...
When I put the ESB lib into my BLE Soft Device the MDK tell me that it have some error in it.
What's wrong in my project? if I need ESB+BLE what should I do?(NRF51822+SDK6...
So I installed the Master Control panel software, plugged in the PCA10000, whereupon I was advised to update the firmware in the PCA10000. The firmware update apparently failed...
