we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Following the instructions from the bluetooth sniffer guide, the sniffer code finds my device. I then attempt to launch wireshark (which has been installed) and I get a plugins...
I'm trying to download a HEX file to an nRF51822 using Keil and ULINK PRO. The hex file was generated by the mbed compiler and works if I drag and drop it using the programmer...
Hello devzone...
My setup: nRF51422 and S110 peripheral
My setup transmits IR data on reception of Bluetooth data from a central device. I have used PWM for generating IR...
I bought 5 Seeed Micro Ble Modules. On their Website they answered a question 7months ago, that they ship with QFAA G0. I connected them via SWD with my nRF51-DK.
God damn...
I am trying to decrypt some data.
My data is encrypted using AES-ECB No padding method.
I know the 32Byte key used for decryption.
Following is the code snippet. I am not...
I guess and hope not but I am a little confused by the compatibility matrix..
I would need to use SDK 7 or higher for my nRF51-DK
but I would need to use SDK6.1 or lower...
Hi,
I searched here for a while and I couldn't find the answer. I implemented custom service by referencing nAN-36 and the github code. For some reasons, the github code...
Hi there,
I am trying to generate a pulse on a pin using RTC1 and PPI. Using a TIMER this works fine but my goal is to incur minimum current consumption by using only the...
I was trying to calculate analog voltage in nrf51822 through ADC.
I used analog 2 pin
ref voltage =1.2v
pre scaler = 1/3
so while i connected 0.9v to analog pin.
I see...
In the sensor datasheet it says one can use SPI_Mode 0 or 3 (doesn't say that there is anything to do to switch between them).
I connected MISO from the DK with SDO from...
I want my application to cooperate with DFU. I am using example DFU project from SDK (6.1) (from nrf6310 folder, i simplified it so it could work on PCA10000), but i need...
I increased my IRAM1 size as advised here , but now my program doesn't work anymore on the nRF51 DK.
I know the problem is somewhere in the memory allocation, because when...
I am working with nrf51422 chips version 2, so according to this table taken from the compatibility matrix v2.0, the last supported versions of SDK/SD/SDS I should refer to...
Also it seems not to advertise. What may cause this problem?
All I could found in the ble_gap.h is:
If both conn_sup_timeout and
max_conn_interval are specified...
Hi
I am trying to debug the "ble_app_hrs" example from SDK 6.1.0 (using keil IDE), on 51822 chip.
The IROM1 is defined to start at 0x16000 (meant to be used with softdevice...
