Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
I am using fds as my file system.
peer_manager is using file system too.
fds_register() is used to register callbacks. But how does the software know which callback is...
Hello
My nRF51 with S120 BLE stack is running as central. I want to connect 3 other nRF51 peripherals at the same time. So in the first step I did a scan and stored the...
Hi,
I'm developing an application based on the nRF52832 and I need a large throughput of over 100kbps, preferably over 200kbps.
I have managed to reach around 128kbps...
Hi
According to BT 4.2 Spec Vol 6, Part F, Section 3.2.9:-
" To write the entire value of an attribute larger than (ATT_MTU-3) octets, the prepare write request and...
hello,
i have a rather basic question concerning the design of the cycling power measurement value field.
how does a simple example for this value look like (variable...
What is the difference between SDK 8 and SDK 12 related to app_timer? I have used it like:
APP_TIMER_INIT(
APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS,
APP_TIMER_OP_QUEUE_SIZE...
Hi Nordic,
I have a star network with 3 nodes and 2 channels. I go through the whole pairing process and start sending data without problem. Now I want to, from the master...
I would like to advertise two different sets of data in parallel, such that one ADV packet is ongoing (say, A), and then I switch to the other packet (say, B) with different...
I tried to make android app for nrf51822 hrm proj.The app flows like this: scan--connect--discover service-- setnotification for every characteristic. The Hrm char was firstly...
Hello,
Could you please advise where I can download an older versions of nRFgo Studio that supports nRF24LU1P? I've got a USB dongle, which I need to re-program.
Thanks...
Hi
I use ble_app_hrs_rscs_relay example with sdk12
and when the APP_ADV_TIMEOUT_IN_SECONDS is reach the nrf52 stop advertising but the on_adv_evt has no BLE_ADV_EVT_IDLE...
Recently I had some strange bugs in few production devices. I inspected newer device markings and they look a bit different:
Pin 1 marking is square not circle.
Build...
Is it safe to use a larger capacitor on the DEC4 pin when using the internal LDO only configuration? So instead of 1.0uF say 4.7uF? Just trying to remove one line item on...
Hi, I need to make a BLE system which sends ADC values from a chip to a receiver kit.
The example most closely resembling this functionality seemed to be the heart rate...
Hi!,
UART works fine with nrf-ble-tutorial-characteristic-CompletedCode in my nRF51-DK but I'm trying to implement in my application but not works.
These are my includes...
