Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I'm wondering, is it possible? This is what I think it will be like if it were going to be implemented:
Acquire the firmware from a host somewhere.
Since the payload...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am working with nrf51822 MC. In my Transmitter code, i am using in low power mode. I was enabled the low power in my code (__WFE(), __SEV(), __WFE()). I measuring...
Hello, I need HID device with NRF51 Dongle.
when NRF51 Dongle insert PC, PC will check it as HID device.
So, could anybody can share suggestion how to add HID on NRF51 Dongle...
Briefly:
Is it possible to switch LFCLKSRC to the internal RC from Xtal with WDT or RTC running? It appears I am only able to do this when Xtal is generating LFCLK...
I am trying to build a ibeacon device, but when iphone in "background mode", it can not get data from ibeacon device.
I used test code :examples\ble_peripheral\ble_app_beacon...
I am working with the nRF51 (PCA100028) dev kit and the nRF51822 beacon to monitor the RSSI of the beacon via the nRF51. To do so, I installed nRFconnect and Master Control...
On the product page: www.nordicsemi.com/.../nRF-Connect-for-desktop
The link from the ' Documentation ' tab is: infocenter.nordicsemi.com/.../nRF_Connect_intro.html
...
Hi,
I have done BLE tutorials [BLE Advertising, Ble Services and BLE Characteristics]
With my NRF51-DK was working perfectly the example of BLE Characteristics (with...
Hi,
I designed a pcb using nrf51 chip with some sensors,
this pcb should read ,every minutes, all values from sensors and saves them into the flash memory beside that...
Dear
Now, I need make one nrf52832 board as USB Dongle, it can be HID device by checked from PC.
And, nrf52832 should support esb protocol, now for esb, I know something...
hai
i was started a bluetooth based project. So i have started with a blend micro.But the range of communication was very short.So i have chosen ble nano with TX power...
Hi
I am calculating the power consumption using
devzone.nordicsemi.com/.../
But there is some point that I don't understand.
When the BLE event type is "Peripheral...
Hello,
the past week I am trying to make the bootloader_secure example work for a custom hardware with no luck. This whole procedure give birth however to several questions...
