Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Hi team, We’re using the STM32H7 as the host MCU and the WMC02C Wi-Fi module (based on the nRF7002) connected via SPI on a custom board. I tried running the Wi-Fi scan example...
I am testing the SDK (v12) Power Profile Example with the DK51 and the nRF51 dongle. My purpose is test if I can lower the power consumption as mush as possible. The default...
I am developing software for a custom hardware based on NRF52. Previously I was tasked on updating the old NRF51 based software (used on older version of the device) for NRF52...
hi,
i am using FDS to store some Data in nRF51 Development kit using temporary application. it is around 2kb. after that i am flashing main Application. is my application...
I am working on a battery-powered application. Since power saving is a must, this design using high-side power node controllers (part number MIC94042) to power-on or power...
Hi
I am looking for pin numbers for the nRF51822 microcontroller.
example like what are the pin numbers for VDD to measure battery voltage..??
I mean in which header...
Hello!
I'm learning how to use properly the saadc for knowing muy battery state of discharge. First of all I'm testing the saadc example which is included in the SDK, changing...
Hi, Nordic
I know when esb working, channel , address and pipe is very important.
From sdk and demo, I can not know these items clearly.
I know these items should be...
I need to use sd_ble_gap_adv_data_set directly and pass custom advertising data, as I need to maximise space and not send the name etc
I have been using mbed which has...
\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I cannot find the define of pin6 pin17 pin21 pin 22 pin24
in this example ...
Hi. Can we develop and use our own firmware for any of the Nordic's beacon? Or do we need to mandatorily use firmware given by Nordic with beacon and modify them as much as...
I am using fds as my file system.
peer_manager is using file system too.
fds_register() is used to register callbacks. But how does the software know which callback is...
Hello
My nRF51 with S120 BLE stack is running as central. I want to connect 3 other nRF51 peripherals at the same time. So in the first step I did a scan and stored the...
Hi,
I'm developing an application based on the nRF52832 and I need a large throughput of over 100kbps, preferably over 200kbps.
I have managed to reach around 128kbps...
Hi
According to BT 4.2 Spec Vol 6, Part F, Section 3.2.9:-
" To write the entire value of an attribute larger than (ATT_MTU-3) octets, the prepare write request and...
hello,
i have a rather basic question concerning the design of the cycling power measurement value field.
how does a simple example for this value look like (variable...
