Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
I have a 51822-DK board. I have followed all of the instructions to set up the environment. Loaded all NRF tools, Keil v 5, install SDK. I began working on the examples. I...
Hello.
I need to hold 64-bit timer value. I store the 32-bit hardware timer value in one variable (low DWORD) and use an additional uint32_t variable as a an upper part of...
Hi, I'm having a bit of trouble getting the broadcast or HRM example to work. I'm using crossworks and after my last question, removed the retarget.c file and the code compiled...
I am new to smart beacon. We have to make a demonstration of our product i a short time. But I could'nt make it run. There are so many sosftdevice, bootloader and application...
Hi,
Basically, I have a DAC 7562 chip with inputs connected to pin 0.17(SYNC pin), 0.18(SCLK pin), 0.19(TX/Din pin), 0.13(CLR pin), 0.14(LDAC pin) with outputs connected...
I just recently upgraded to SDK 7.2.0 and am now using the keil pack installer as well. First of all, I really appreciate the ease of this new system, but I'm running into...
The new softdevice v8 states that previous revisions(1 and 2) don't support all the new features, and I'm curious how to determine what revision my ic is.
thanks,
akbar
Hi
I have recently purchased an Adafruit Bluefruit LE board ( www.adafruit.com/.../1697) , that uses the nRF8001 chip, so that I would be able to send iOS notifications...
I have a new nRF51822 kit, and although I can (apparently) configure the beacon, it always shows "Beacon not found" when I try to use it.
I'm using an iPhone 5s and the...
Hi, I got new NRF51-DK and dongle with 51422 chip.
It seems that the layout of the memory map has changed with the new SDK and I can't find any information how it should...
After I uploaded hex and dat file which is compiled from sample beacon source code in SDK to nRF51822 Beacon Kit via nRF master control panel app, I got Upload failed GATT...
I have done some testing and debugging, but I can't seem to get the nRF51 DK working with the beacon example project.
I used the keil v5 pack installer to access the ble_app_beacon_s110_pca10028...
I've noticed that the L2 value has been changed from 10nH to 27nH in the reference layout and on the new boards (DK and Dongle). This value is only for LDO setup (from PS...
