Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I currently have an application with DFU bootloader that runs on s110 5.2.1 on a rev1 nRF51822. If I upgrade to the latest rev3 chip, can I just flash it and everything will...
How can I compile a simple blinky program for the PCA10024 with the IOT SDK, and using the (iot modified) s110 softdevice?
I've been trying to get a simple blinky program...
Hi all,
I am facing a problem with pstorage_init() function. In fact after enabling the softdevice (S130), I am calling the pstorage_init() function. When debugging, the...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
Hello,
I am new in this using of this RF module. I have tested it in many ways. But I'm using this module with pi16f72 So, it has " SDO,SDI,SCK" I have crossed the cable...
I'm working on a project where we're having mulitple nRF51822 chips communicate in a multiceiver way. When we bought the nRF51822 chips, the technical sales rep claimed that...
Hello, we have kind of an in-house serial command protocol that we have used over Rs232, sockets, wifi, etc, and we would like to implement it over BLE. I am inheriting a...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi I'm confused by this statement... Can my characteristic size be more than 20 bytes?
Each outgoing data packet can contain up to 20 bytes of user data (set by the specification...
Hello! What is maximum number of bytes can I send from Central/Peripheral to Peripheral/Central device in one packet? Can I send more than 200 bytes in one packet? I want...
Can anyone point me to sample code that exercises ANT's "advanced" burst mode? I have sample code provided by the Keil SDK that contains a prototype for function sd_ant_adv_burst_config_set...
I'm actually writing some data to the flash. I'm using pstorage api interface.
But whenever I flash the new firmware, I get some garbage data.
in my main function I would...
Posting this question here as there seems to be no Tech Support available in India.
I am looking for a BTLE solution that can be used in my BT device.
The functions...
My Problem
ble_app_uart app hangs at main.c line 503 " ble_stack_init(); "
My Setup:
SDK: nRF51_SDK_8.0.0_5fc2c3a
Device: nRF51 DK
Editor: CrossWorks
...
