Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi
Please tell me someone about the causes and countermeasures!!
I Connect the board & JlinkLite and tried the flash write.
Softdevice Ver6.2.1 -> Success
Softdevice...
Unfortunately, I'm not seeing NRF_EVT_POWER_FAILURE_WARNING events on my s210 based system. As I've seen in other questions on the forum, I've implemented the calls below...
I'm currently trying to merge the S120 softdevice with the compiled code from the ble_app_multilink_central sample under Linux (Ubuntu).
Here is the command I'm executing...
There are a couple problems with the SDK 7.1.0 implementation of nrf_delay_us for GCC. The experiments I've run show the provided version generates delays 40-50% too long...
Hi,
I am developing an application to capture data on a PC over ANT+ using the ANTUSB-m as slave and the nRF51 DK as master.
In order to test my program I want to be able...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I am trying to use the nrf51822 to send media button commands over HID. I have seen several questions on here and they usually involve the HID Mouse example (which doesn't...
Hello,
I have been trying to implement AES in order to encrypt a time stamtamp to be sent in the advert of the iBeacon ( 128 bits, using Minor and Major bits, (16+16)*4...
Hi,
I am trying to decrease circuit power consumption that's why I am using sd_ble_gap_tx_power_set(TX_POWER_LEVEL) function. When I set TX_POWER_LEVEL as 4 or -20, I dont...
We are looking to change tx_power setting to Neg30 dBm and for this we have accessed NRF_RADIO->TXPOWER = (RADIO_TXPOWER_TXPOWER_Neg30dBm << RADIO_TXPOWER_TXPOWER_Pos);
...
I have the NRF51 DK working with CrossWorks on OSX. I have the blinky example working.
Now I would like to figure out how to get very basic HELLO WORLD type demo to iOS...
I am implementing dual bank DFU on the PCA10001 board using the latest SDK (7.2.0) and S110(7.1.0). I am able to enter bootloader from my app as detailed here:
developer...
I'm just reading the documentation regarding the analog digital converter and wonder why there is one bit in the configuration register for every analog input. What will happen...
I'm using a relatively large GATT db that has rd_auth and wr_auth set to true for every characteristic. This prevents the stack from automatically replying with cached values...
I'm using the MAX9814 electret pre-amp's output as an input to an analog pin of the nRF51822. The MAX9814 has a 1.2V swing at 1.2V DC (so it goes from 0 to 2.4V). VDD for...
