Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hello,
I am trying to implement wake on motion functionality of MPU9250 with nRF52.
I am writing below sequence code for wake on motion configuration:
void MPU6500_StartMotionDetection...
Hi DevZone
I want to make a little beacon app, that advertises on channel 37 then waits 700 ms, advertises on channel 38, waits 700 and advertises on channel 39.
The below...
HI,
I wan't to read sensor data from ADC. So i use nrf_drv_saadc_sample() .
On Arduinos i usually call value = analogRead() and after that i process the data. But here the...
Hello,
We need to add custom data to advertise packet. As I understand we can use Manufacturer Specific Data. But to do this we need to get our Manufacturer ID from Bluetooth...
I have the following code for a custom service UUID and a custom 128 bit characteristic ID. I get a error of no memory available in our_char_init while adding the 128 bit...
Hi,
We bought a mac bd addr pool from IEEE
Where is the best way to store this mac adress during production ?
We guess the type will be: BLE_GAP_ADDR_TYPE_PUBLIC
Do...
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi. I'm using nRF51822, SDK12.2.0, S130.
I finally compiled bootloader_secure which was very hard.
Q1. After run bootloader, I can find the device using DFU "DfuTarg"...
Hi ,
I am trying to use the new softdevice SD130 V2.0.0 and have not had any luck when using the most recent version of SD130. I ran the same application with SD130 V1...
I've nrf51dk development board. It has nrf51422QFACA10 chip and has 32kB ram and 256kB flash. I downloaded sdk V11 and programmed ble_app_beacon_s130_pca10028. It worked fine...
I try to move my project from Keil to GCC but I get some different behavior. To show the difference I use examples/ble_peripheral/ble_app_uart
The part of the code below...
I have purchased a nRF52 DK and want to use it by emulating an ANT+ Stride Based Speed and Distance (foot pod) and pair that with my Garmin FR235 running watch in order to...
Environment:
Segger Embedded Studio
nRf51 Developementkit using jLink OB firmware
S130
We're using the \nRF5_SDK_12.2.0_f012efa\examples\ble_peripheral\ble_app_template...
I'm trying to enable interrupt for radio events.
I have this code in main:
bsp_board_leds_init();
(...)
NRF_RADIO->INTENSET = 1 << RADIO_INTENSET_READY_Pos;
NRF_RADIO...
Hi!
I would like to create a RTC for stamping log messages, with 1ms resolution and including time from year to millisecond, like: YYYY-MM-DD HH:MM:SS.mmm.
What would...
