I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
I'm running a custom nrf8001 board and the nrf8001 is consuming approx 6.2mA on it's own in advertisement mode using the uart demo. Has anyone had this same problem? Any advice...
Flash write and erase works fine, if ble is not initialized( ble_stack_init()).
Once ble is initialized, any write to NRF_NVMC->CONFIG hangs the system.
Do I need to...
Hello!
We are using a custom hardware design based on nRF51822. Recently we switched to the new chip version QFAAG0 with softdevice 6.0.0.
Our application needs a repeating...
I have tried HTS(Health Thremometer Service) sample Program on nRF6310, PCA10006, SEGGER J-Link Lite and iPhone5C.
First time, temperature is displayed on the iPhone5C...
Hi,
I have a custom board with nRF51822 chip on it and tried to run the proximity sample program on it. I have used the nRF51822 develpment board + nRFgo Motherboard to...
www.dropbox.com/.../Screenshot 2014-04-03 11.41.25.png
I guess has nothing to do with crc16?
the call stall seems unreasonable, is it because my stack is messup?
...
Hi,
Is it possible to control the drive current of the gpio pin?
Can anyone explain the different possible drive configuration for gpio's (S0S1,H0S1, etc..)?
Regards...
I'm trying to compile the bootloader for gcc from this post: devzone.nordicsemi.com/.../nrf51822-over-the-air-bootloader-with-gcc
The bootloader start (I can find my device...
Hi,
I'm confused with the functions (sd_power_mode_set and sd_app_event_wait).
1.I think there are described with the same function.I can't tell the difference between...
Hi,
I've developed an application and tested it on the evaluation kit. Now i'm trying to run it on a custom board with a nrf51822 chip on it. I've made modifications to...
Hi,
I use to the nrf51422 with nordic's dev/ev kit.I want to build a project and the purpose is to get the sensor's date and use the ant protocol to deliver the date to...
Hi,
i need some help by selecting the right Hardware for a new Project.
I want to build mesh network so i think ANT is the right Protokoll for me, with BLE i can't build...
Hi
I have a BLE module of nRF8001 chip and everything is working fine with it.In your Arduino compatible libraries for nRF 8001 you have a function hal_aci_tl_init() in...
