I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
I have a custom hardware running on nrf52840 and using ncs 2.6.1. I have implemented a custom authentication flow with customer characteristic along with the BLE bonding....
Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Recently I open the sdk of the nrf51422,there are some functions that indicate that they are come from the document call 'ant_interface.h'.But when I try to go to the definition...
I'm ending up in the HardFault_Handler() on calling sd_app_evt_wait() within a function that reads from the UART. What might cause that? Stack screenshot attached.
I have...
I'm using nRF51822 for development. and I want to use ADC to measure the electricity of battery, but I don't know the discharge characteristic, i couldn't get that on internet...
#define IO_CHERRY8x16_ROW_PORT 0x13E02040UL
#define IO_CHERRY8x16_COLUMN_PORT 0x60031FBFUL
Why this number be defined like this ? What are this two things use for?
...
Hi,
I'm trying to compile the bootloader example using GCC instead of Keil compiler.
To do so, I copied the bootloader example and started editing the file bootloader_util_arm...
Hi, I am working on my new project. My goal is a sensor network. I have to create four service, one or two basic service like htm and battery service and other with contains...
Referring to the PCA10001 schematic, there is a solder bridge SB1, which connects AVDD with VCC_nRF.
Can you please explain in which cases is it needed?
Thank you
...
Hi all,
I test the DFU as follow:
erase chip, program "s110_nrf51822_5.2.1_softdevice.hex"
program "bootloader" by using nrfjprog.exe
"DfuTarg" can be found...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I'm trying to build the bootloader for gcc/Eclipse.
I used the manual setup approach described here.
However, I can not fit in the allocated space, because...
SDK version: 5.1.0
S110 version: 6.0.0
chip: nRF51822
I am experimenting a generic Data transfer hid device, the report map is as follows:
0x05, 0x0C, // Usage...
Hello Nordic team,
I am working on a BLE RedBearLab shield (nrf8001) mounted on an Arduino board.
Consider that a connection is correctly made from a Master app to my...
I've been running various code on a 51822 that has used PPI, timers, events, GPIO pin config and so on. Supposing I've lost track of what state the retained registers on the...
Hi,
I am new to ANT programming, and was following the userguide's steps to set up my nRF51422 evaluation kit (pca10003 board). I can compile and upload the blinky example...
