Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
am using nrf51822 chip communicating with PIC16fl1509 through uart.the PIC will send the temperatire values through uart to nrf51822. i have a doubt ! will the uart communication...
Hello,
The fact is that I was testing how to OTA update the kit's firmware. I had no problems with the app but when I tried to upload the bootloader.hex includen in the...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
friends :
i assume that the nordic support team can also be considered as friends.
i purchased a nrf51822-mkit, but it seems that it does not qualify for a legitimate...
Hi guys,
I would like to know how to use the softdevice to enable an interrupt when I receive an advertisement packet. Right now I know we have to use
softdevice_ble_evt_handler_set...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Good morning,
Is it planned to raise a new version of this application note but based on the new version of the SoftDevice? If yes, when is it expected?
Best regards...
Where could I find the software for the Connectivity chip(ATSAM 3U2C) that enable the mbed connection?
If I flash the EK board with this software, could I use EK(evaluation...
Prior question: nrf51422-soft-device-options
As a follow up to my previous question, has Nordic developed a stable boot loader to use with the S110 soft device and the...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi guys,
I can get a rand number use the API:err_code = sd_rand_application_vector_get(buf, bytes_available); but the question is that How can I get a rand number just...
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have a strange problem with pstorage function with nrf51822 with s110 v6.
I need to use nrf_delay ( about 1 second long ) after store and before read.
This is the source...
