Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
Hi,
I 'm using MCP v3.9.0.6, softdevice v7.2.0 and pca10003 board.
After load bootloader program to board. I use MCP to load application for it. In MCP, I choose device...
HI People,
I use nrf51822 CEAAE00 (0x0079) chip which has 256 kB FLASH, 16kB RAM. I faced a problem when compiling the bootloader for it. The solution was I am using a...
I am trying to build a custom board, based loosely on the nrf51-DK (which I have been testing). I haven't ever directly programmed a chip before (always used interface MCUs...
if I send only the advertisement, it sees that data
Is there something in the IOS that prevents seeing manufacturers data in both the advertisement and response packet?
I found the Ble Serialization here and the example sourcecode within the sdk sources.
The sources are for using S110 softdevice.
Does Ble Serialization also working...
Hi, I'm trying to get my nRF51 code (which works on my dev machine) to tun on the test server (both Win7). Am using MasterEmulator 2.1.10.8567
The dongle itself is happy...
Hello I am new to this platform, can anybody tell me how to write the value on serial in NRF51822
and what is the command through which i can write the value on serial. getch...
My application uses ble_radio_notification_init. Every time I switch from my application to the DFU bootloader it drops the connection about 10 seconds after starting the...
Trying to follow
devzone.nordicsemi.com/.../
but whatever I do, I am unable to make Eclipse discover the include paths or the source file paths from the makefile. I've...
Hi,
My Nordic kit just stopped detecting from last two days.
I have also check this in other PC also.
It detects some times some times not.
I am using Windows 8.
I...
Hi all,
I would like to know if it is possible to use the uart before the actual bootloader runs... I need to communicate with the master uploading the firmware before...
Hi All,
I need to implement a kinda a mesh network of Nordic device nodes placed nearby to act as a relay, for that I have a use case where following requirement.
...
I'm porting a nrf51 project to nrf52. I'm using softdevice s132 1.0.0.3 alpha. When compiling I get a lot of L6406E errors and a L6407E error. Do you know what's causing this...
hi,
I should how to transplant the official DMP mpu6050 library to nrf51822 above?I don't know how to transplant it and could you tell me how to transplant it?
