In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hi,
I'm trying to connect to the EMQX(what I made on GCP) using mqtt protocal. I'm using the sample code that nordic provides in lesson. Based on the Exercise4 code which...
Hi I'm having the exact same issue found in this post:
I've only just started evaluating the board and haven't gone as far into measurements as that poster, but something...
When we add a uuid will follow the steps below
err_code = sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type);
// Add the service.
err_code = sd_ble_gatts_service_add...
I was looking the way to set different tx power values and also figuring out a small bug in the interface when you switch among payload models and payload length is >1.
Bug...
nrfgo_error.docx
Using nRFgo Studio as the interface I try to download the file “set_in _test_mode.hex” and get the error above.
What are the proper steps to get DTM...
I am trying to reset and halt the target nRF51822 under SWD protocol.
Could someone point out the register to achieve the same? I looked up the reference manual but couldn...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart" as reference.
As I've researching nRF51 with Central device,
it returns
Packet 0 : 020105 0c094e6f726469635f55415254...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
My setup is as follows
1 Gyroscope + Accelerometer
1 RTCC
1 SPI Flash device
I want to set up the PPI to periodically sample the MEMS devices and the RTCC...
Hello,
I am trying to remove the use of the frame pointers for bootloader_util.c because I am getting the error : "r7 cannot be used in asm here", but I only know how to...
I use nRF51822( BLE nano) central mode to connect annother BLE nano (ibeacon mode), then I call disconnection to the peer address. Sometime, the disconnection callback will...
hi,
i am trying to send data using ble_uart app.
in this app i am using timer difference to send data. when i am getting 1st data in uart event handler. when i am printing...
I would like to implement DFU OTA updates without the Master Control Panel, and I have a couple questions:
Is there example code for the client-side of the DFU service...
Our personal phones are set to auto-update iOS apps. Unfortunately our team all got the latest version of the NRF Toolbox app (v2.5) released on February 5th, 2016.
Previously...
hi,
i want to execute a block of code in which timer should start. and stop at end of the block. and the timing depends on manual interrupt. and restart again when the execution...
Im using a board that is not one of the officially supported nRF51822 boards. Im trying to get the ANCS example project to work, but It wont broadcast or even turn on the...
