hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
I am trying to communicate with a SPI peripheral, using the nRF52 as the master, and the peripheral as the slave. What happens is that it still faults out, and the presence...
We are currently developing an Android app (5.0) supporting the peripheral mode and communicating with the Master Control Panel (v3.7.1).
The connection to the Android...
Hi,all.i faced a problem:when i take my phone far away from my device,link lost service can work normal and my device can alarm.But if i turn off bluetooth switch on my phone...
Hello everyone,
i am trying to mix up both services proximity and RSSI but i am not able to merge the header files of these two services can anyone guide me? how to merge...
Hi,
I'm converting my project to OSX GNU from windows keil because of license problem.
There is some .o files made by keil-arm complier in my previous project.
and...
Hello,
Is that possible to force carrier frequency out of 2.4 GHz band (modify canals) for a special underwater application (2.4 GHz is not adapted so i whish to move on...
Hi,
I want to detect long and short press in same button.
Define "BUTTON_DETECTION_DELAY" can detect one delay.
Let me know to detect more than two delays.
Hi everyone,
I'd like to use the micro-esb radio interface to let to nRF's talk to each other. One of them will be generating 4 PWM outputs based on data received.
I have...
Hello Nordic,
I am trying debugging on following project [--ble_app_lbs_master--]. During debugging, I never reach at app_button_is_pushed function. I tried pressing the...
I have built a PCB that uses the nRF51822 . I am failing to load the binary onto the chip via the nRF51 DK. I can:
connect to the nRF51822 on my mac using the JLinkExe...
