Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
While getting myself familiar with new SDK12 features I've noticed that when nrf_log uses deferred logging to RTT NRF_LOG_FINAL_FLUSH() results in unconditional breakpoint...
Hi guys,
Wanted to play around with the new SDK and the S332 Softdevice. I tried your multiprotocol example "ble_ant_app_hrm" with Keil.
Build fails:
http://dumptext...
Hi,
I am developing an app using the base module "ble_app_uart". In our application we would like to store data in the flash memory.
I am using "Flash Data Storage"...
I want to make my nRF52 turn on every 5 minutes, send data to a device over BLE and go back to sleep. For some reason once I turn on BLE advertising LED1 becomes solid and...
Dear Nordic Team,
Thanks for supporting.
We are worked in nRF51422 development kit.How can i enable DFU service in all BLE APP examples source codes in main.c
Please...
Hi,
when I use nRF Connect (or MCP before) to browse my BLE service, I get shown some garbage if I use many characteristics in my service.
When I use 45 characteristics...
Hello people,
I'd like to use the NRF52832 (QFAAB0) / PCA 10040 / S132 development board as a data logger. For that I soldered a micro-sd card reader and started using...
I set the connection as follows:
#define MIN_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(1000...
I am trying to use the mesh network using the nrf51822. I have to use the app_timer with my application. Mesh library and the app_timer library making conflict with the SWI0...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
I have checked the datasheet between 51422 and 51822,they look the same,but why the NRF51422 can flash BLE and ANT+,but 51822 can't? Is the Radio part different,or the Flash...
I have based my firmware on the Proximity Application example.
Now I need to extend my application to support BLE DFU service.
But as i read Extending your application...
Hi,
I am using the flash memory for a few variables and it works very well. Now I have one flag which is defined by #define statement and if it is enable then the initial...
hi,
i have nrf8122 module . want to flash a hex file in it by using nrf51 development kit. is it possible to flash code in the nrf51822 module. other wise please provide...
