Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello
I've found your example in the dev-zone and migrate the project to SDK10 and will probably do the same for SDK11.
However, I've got a problem in my project. When...
hi,
i want to implement rtxos in my nrf52832 application. one of the nrf52832's feature is ARM Cortex -M4 32-bit processor with FPU, 64 MHz.
my question is, why the...
Dear Nordic.
I am developing bootloader without SD (s120_nrf51822_1.0.1).
And after execution of bootloader, jump to application working with SD.
Flash composed like...
I tried to compile blinky sample in SDK12 with make tool-chain. I got 3 errors:
Makefile:214: Cannot find include folder: ../../../config/blinky_pca10040_s132
Makefile...
I converted a project from uVIsion to IAR, and I get an error when I use app_timer_start(); the error says: Error[Pe167]: argument of type "void ( )(void)" is incompatible...
I don't need to connect the master with the peripherals, but i have to know how is the maximun quantity of scan response that can accept the master.
In the example ble_app_multilink_central...
In trying to move to SDK 12.0.0 from 10.0.0 I get the error:
"...components/includes/app_error.h:33:23: fatal error: ant_error.h: No such file or directory
#include "ant_error...
Hi,
I want to run BLE mesh network example on my Dev board to understand it better.
I am running it on SDK v8.1 and using ble_app_proximity example S130.
Following...
Hello,
I'm using the "experimental_ble_app_blinky" on the nRF52 DK, and I would like to reduce the power consumption during the advertising.
Indeed, during the advertising...
Hi,
I am currently designin one of our product with a nRF51822 QFAC included, and I need to store 17k-bytes in a non-volatile memory.
I am writing the firmware using...
HI,
I am reading LIS2DH accelerometer sensor data to nRF51822 MCU and displaying on hyper terminal. The LIS2DH sensor gives output in the
form of digital through SPI or...
Are there plans to create a nRF5x micro that has finer control over the RF power output? I'm currently using an nRF52, and the 4dBm steps are pushing the limits of our intended...
Hi. I'm using PCA10028, SDK10.0.0, S130.
Q1. I want UART to start or stop whenever I want. It's to save current consumption.
There is "uart_init()" for reference, but...
Hey folks,
i need to programm a nRF52 dev. kit to advertise data and receive advertisings sequentially, without connecting any device. It means that i need to advertise...
Hello everyone,
I have inherited a project from my coworker. It uses NRF51822 QFAAH0 , SDK 4.4.2 and S110 5.2.1 . My device is scheduled to: advertise, collect the data...
