I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hi
Regarding the NFC url example there is any way to change the URL dynamically. My idea is to, at a certain point, be able to modify the URL configured during the setup...
Hello,
I'm having an issue when trying to update the bootloader itself: NRF_UICR->NRFFW[1] returns 0xFFFFFFFF, which means I can't use the MBR command to swap bootloaders...
Our BLE product uses a meander PCB antenna similar to PCA10031. It works actually quite fine, but a question pops up when it comes to tuning.
Antenna matching design in...
I'm having some issues getting the auto ACK to work properly. I am only receiving auto ACK messages on the first 3 received packages, after which the receiver stops replying...
Hello i have a system that build in an ultrasonic sensor RedBearLab BLE Shield ( nrf8001 ) and arduino i want to get ultrasonic data via bluetooth and see it on nRFConnect...
Hi,
My host MCU controls nRF51 over SWD interface.
How can stop/halt nRF CPU? After initialization the SWD(init/read DB/AP AHB, etc.) I need to halt (stop nRF program...
Hi,
I would like to have one page of flash mapped manually to store information critical for the device. Let's assume I do not trust data preserving by DFU or there is...
I have some BLE traffic that I have sniffed and am displaying in Wireshark. Most of the opcodes (read/write request/response indications/notifications etc.) are parsed/displayed...
I am trying to develop a GATT service on nRF51.
The GATT service measures a few values, and stores them in a characteristic. When the GATT server (phone) requests data...
I am trying to build a device to stream the 9 axis sensor data from the I2C based sensor and then transmit it using BLE UART profile. It is sampled every 3 seconds using app...
I am using an nrf51422 board. I want to update via OTA using ANT+ Dongle. The device information shown in the OTA Updater is parsed from the Bootloader Code. Is there any...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
We're quite interested in producing an nRF52 design based on the solar beacon (great design, and clean software). I appreciate the relative simplicity and manageable BOM cost...
Hello,
I am developing a system that samples 3 independent data using SSADC. since the timing was important in my system, I decided to use PPI to trigger the SSADC.
However...
