Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
My host MCU controls nRF51 over SWD interface.
How can stop/halt nRF CPU? After initialization the SWD(init/read DB/AP AHB, etc.) I need to halt (stop nRF program...
Hi,
I would like to have one page of flash mapped manually to store information critical for the device. Let's assume I do not trust data preserving by DFU or there is...
I have some BLE traffic that I have sniffed and am displaying in Wireshark. Most of the opcodes (read/write request/response indications/notifications etc.) are parsed/displayed...
I am trying to develop a GATT service on nRF51.
The GATT service measures a few values, and stores them in a characteristic. When the GATT server (phone) requests data...
I am trying to build a device to stream the 9 axis sensor data from the I2C based sensor and then transmit it using BLE UART profile. It is sampled every 3 seconds using app...
I am using an nrf51422 board. I want to update via OTA using ANT+ Dongle. The device information shown in the OTA Updater is parsed from the Bootloader Code. Is there any...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
We're quite interested in producing an nRF52 design based on the solar beacon (great design, and clean software). I appreciate the relative simplicity and manageable BOM cost...
Hello,
I am developing a system that samples 3 independent data using SSADC. since the timing was important in my system, I decided to use PPI to trigger the SSADC.
However...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello all
I am trying to implement hardware flow control for UART.
is there anything else to be done ? I have done the GPIO configurations like this
const app_uart_comm_params_t...
Hi,
I'm trying to migrate from SDK 6.1 to SDK 7.2 on custom board.
In SDK 6.1 everything works fine (SoftDevice v7.1.0), but with SDK 7.2 I get into HardFault Handler...
Hi My project need to transport HRM data by ANT+/BLE. base on ANT_s332_nrf52_0.9.1.alpha.hex and sdk nRF5_SDK_11.0.0_89a8197 platform. We have finished the function. Now we...
Hi all,
I know that there is a field "address type (public/random)" in white list.
When a scanner send scan request to an advertiser with public device address. this...
