Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Please teach me the minimum theoretical value of the transmission time in the following conditions.
CPU --> nRF24L01 --(2.4GHz/1Mbps)--> nRF24L01 --> CPU
CPU -->...
I need to send a long (let's say 10Kb) notification from Bluez 5.37 on my Linux device to a mobile phone.
My implementation is based on src/shared/gatt-server.c .
I...
Hi,
I have put in my chip (nrf51422):
-1 softDevice s110 8.0.0;
-2 application (hrm_whit_dfu);
My problem is:
when i send characteristic to start advertising the board...
Hi everyone,
I am new to nRf series and have just started to use the nRF51 Development kit(nRF51422). I am using the s130 softdevice and I have seen that the sofdevice supports...
I'm trying to test out pin change interrupts using the PCA10028 dev board. I'm using two buttons to turn off and on an LED. The code below is only generating events from button1...
I have a custom board designed which implements a Arduino Micro (ATmega32U4) and an nRF8001 chip based upon Richard Clarks' nRF8001 breakout . The Arduino FW uses a slightly...
Hi.
Is it possible to enable the encryption of data which corresponds to the particular characteristics? i tried with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, for setting the...
Hi,
how is the new nrf_drv_twi supposed to be used for reading registers?
The sequence for that is pretty much industry standard:
> Device address
< Ack
> 0x00 (register...
I'm running the ble_hrs example provided on my nRF52 board. The thing is, I'm unable search my device using both nRF Master Control Panel and normal Bluetooth connection from...
I am using a central S130 softdevice in an nRF51822. I connect to a peripheral using sd_ble_gap_connect(&m_peripheral_address, &m_scan_param, &m_connection_param) . If it...
I am trying to provide a custom peripheral service with a 128-bit UUID in an nRF51822. I would like to use two bytes of the UUID to encode a piece of information unique to...
Hello,
am I right to assume that if sd_ble_gattc_write returns anything other than SUCCESS, then the packet was not queued?
Is this also true for BLE_GATTC_EVT_WRITE_RSP...
Hey guys,
I have a little problem on a new board comunicating with a MPU9250 sensor.
Chip version is nrf52832-QFAA-BA
GPIO PINS Used P0.20 (SDA) and P0.21 (SCL)...
The S332 v0.6 has been released and it is supposed to be compatible with SDK11. My concern is that in the release notes of SDK 11, it says "Temporarily removed support for...
