Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
I am still noticing a higher than expected power draw on my nRF52 and I want to make sure I have adopted best practice in turning things off/optimising things before entering...
Hi,
I am using a 128KB-rom 16KB-ram nrf51822 and trying to run blinky from SDK 11 with softdevice.
If I load nrf51 S130 1.0.0 softdevice, and use the following in my...
As of SDKV12, because of the removal of pstorage, I upgraded my app to use fstorage.
If you look at the SDKV12 doc at this link, you will notice that it is quite lacking...
Hi,
I am trying to write some data into the flash of the nRF52832 SoC, but can only write around 5 kb of data. After that I will get an error of number 7, which should...
I'm using SDK v11, nRF51
I started developing with S130, v2.0.1
The device is peripheral only, so I decided to switch to S110 v8.0.0, since I need the memory.
I made...
I don't have a particular issue right now, just a concern that I have because my device needs to be bulletproof when it comes to reset behavior.
When sd_mbr_command(SD_MBR_COMMAND_INIT_SD...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
Hello,
I'm developing nRF52 with Keil5.14.
Before I used nRF52_SDK_0.9.2 and it worked fine.(With NordicSemiconductor.nRF_DeviceFamilyPack.8.0.3.pack)
I upgrade the...
Hi all
According to the following post, the RAMONB register doesn't exist since the nRF51822 has only 2 RAM blocks: devzone.nordicsemi.com/.../
But the current version...
Hi, i use the SDK11 and i will send and receive beacon and be able to launch a BLE DFU.
I am able to make a software in wich i can receive and send BEACON but in...
I'm trying to upload via DFU from one nRF51822 to another nRF51822 via DFU
The receiving side is not a problem as there there are loads of examples.
But I can't find...
Hi,
I'm developing some code for an AVR MCU with the Adafruit nrf8001 and had a question about the expected behavior of the handshaking lines, REQN and RDYN
My understanding...