Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi all,
Is it possible to get a callback from the softdevice, when a characteristic is changed? If so can you guide me in the right direction - documentation / examples...
@brief Function for application main entry.
*/
int main(void)
{
// Configure LED-pins as outputs.
LEDS_CONFIGURE(LEDS_MASK);
// Toggle LEDs.
while (true)
{
for...
Hi,
I'm using gazell library with app_pwm.
From documentation gazell use Timer2 and PPI channels 0,1,2.
APP_PWM use Timer0.
When I disable pwm using app_pwm_disable...
Hi,
I'm trying to use the nRF52832DK to flash a Rigado BMD-300 module (nRF52) - I've connected SWDIO, SWCLK, GND and voltage sense to P20.
It seems that because the...
I run the boardcast tx application on a nRF52832 board and I add uart drive into the proj. I use UART to console on PC.But uart doesn't work, PC console nothing. What's wrong...
I'm using the mouse example which use bonding and white list which allow to connect only to one central after performing the bonding
my question is, does the bonding feature...
Hello,
Is this the correct setup? What else will I need to do to make it work (e.g. it says something about the MCU will detect the external board and then programm/debug...
I want my device to pair only with a single central device at a time. So once it gets paired, it should not be able to pair with any other device. For this purpose I use directed...
Hi community,
I'm studying the possibility to be able to link multiple central devices to one peripheral. As it defined in the s130 soft device description ( www.nordicsemi...
I upgraded Arduino IDE to 1.6.8 version, it was automatically set up Programmer AVRISP mkll, in previous version I can see that was Atmel STK500 development board
in Tool...
Hi.
I'm trying to get audio controls (mostly volume up/down) to work with apple and android phones. I've used as base your HDI keyboard example.
It seems to work OK...
I have a BLE peripheral application based on the nRF51822, running Soft Device S110 with SDK 8.1.0. The centrals are mobile apps, one on Android 5.0, one on iOS 8.4.1.
...
I'm using the UART driver (drv_uart.c) provided with the nRF5 SDK 11.0.0 on a nRF52 chip and once a NRF_DRV_UART_EVT_ERROR event is received, the receiver seems to be stuck...
Hello all!
I'm researching Radio Notification. I had read define and tutorial . But, It don't make me clearly.
Could you explain more deeper about Radio Notification...
Hi,
I just upgraded the SEGGER RTT source files from V4.98e to the new V5.41b for a nRF51DK project using gcc/Makefile. When linking the (now quite large) program, I got...
