Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Dear Developer Zone,
I'm using an nrf51822 with SDK8 & SD S110 v8
We have an iOS app connecting to a custom service on the NRF device. What we would like to do control...
hi,
i have a project which need dfu by OTA,but nrf51822 flash is not enough.The project detail information in the following:
chip:nrf51822QFACA10
SDK6.0
SOFTDEVICE:7.3...
I'm using nrf_drv_twi to talk to an accelerometer from an nRF51822 on a custom board. I'm on SDK 10.0.0. I'm following the example from the SDK, peripheral/twi_sensor. And...
Hi,
I set advertising data as follows:
err_code = ble_advdata_set(&advdata, NULL);
But I can't achieve advertising without ScanResponse，could you give me some suggestions...
Hello,
I do connections between 2 nrf51 with a known and static services. Is that possible to bypass the discovery to access a characteristics (i know all characteristics...
Hi,
I am having problems using the the dfu_dual_bank_ble_s110_pca10028 example on a nrf51822_xxAA device.
I have changed the memory ares to:
IROM 1: 0x3C000, 0x3C00...
So long story short - I need to pair two devices: Arduino UNO with Seeed BLE Shield and Adafruit Feather 32u4 Bluefruit LE.
Now, Seeed shield is configured, and is able...
Hello, I am now having problems to get NRF51 DK to work. My computer is connected to board with USB. It can recognize it.
Now, here is what is something strange, when...
Not sure if this is the correct place to ask this question.
I can't seem to find the download location for the Master Control Panel PC application. It seems to only available...
Hello,
I am currently trying to generate a PWM signal on P0.00 and am not having success. If I drive P0.00 without PWM, everything works fine. Is there anything that would...
I have 2 nRF51 Development kits and a nRF51 dongle that I am using for proof of concepts. I am mainly using the nRF51 IoT SDK because we are looking at using IPv6 with 6LoWPAN...
I'm looking at log_uart_init in the nRF5_SDK_11.0.0-2.alpha and wondering if it would make more sense to allow the application writer to pass in a baud rate.
