Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
(assume all resources being used)
This may also include consumption at Start-up.
i need this to calculate my power requirements for a special module being developned...
Hello!
I want to create my first BLE devices and nrf52 is a choise. Devices should work as described below and before I purchase few nrf52 DK I want to be sure that it...
hello
I am a beginer to design with wireless and I would like to know with soft can be used if i have one master with 4-6 slaves. It seam to be a S120 it right ?.
Also...
Hey all. I'm working on a really simple beacon application and I'd like to use RTC0 when the BLE stack isn't using it... is that possible? No BLE connections, just 1 advertisement...
Hi,
I'm facing a weird problem resulting from the following code:
while((!twi_tx_done) && timeout--);
The main file and the MPU9150.c which includes this command...
Hi, I try to capture ipv6 over ble packet.
So, I construct system like, nrf dk 51(with sensor) - rasp
nrf-dk 51 is equipped with coap-server source and rasp doing like a...
Hi everyone,
I have a really weird problem.
I created a makefile based on Nordic's example from the app_template and created 2 additional targets, one called "debug" and...
I have upgraded my laptop to Windows 10 and all hell break loose.
When I either connect the board or the dongle, they are stuck in a loop of connect/disconnect behavior i...
hi,
i am using ble_uart example in which i am sending 3 byte of midi data
(90 1e 45 0a .E.)
i am getting (.E.) when i converts this ascii value to hex value i get (2e...
Im trying to provide DTM functionality for certifications tests. I can't setup an UART interface, I found the below code which tries to use DTM without UART. it uses channel...
Hello,
I've read a lot about trouble people had when they used bluetooth and flashed the rom without using the propper softdevice APIs.
What is the issue with concurent...
Good morning.
I ´m working with nrf51-dk, sdk 9.0.0 and softdevice 110.
I have done a proyect without softdevice, only uart and master spi (mode 0) and works perfect...
Hi, I flashed the Proximity Application to nrd51822,with s110_nrf51822_6.0.0-5.beta.
the chip run right, and I used the NRF Master Control Panel, when I write data 0X02 to...
