Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
image description (/attachment/6196b4481c3f6fefbd0784b78d9163c9)
Hello.
I development education robot by ENTRY base.
PC(ENTRY base) + NRF51822 central
and
NRF51822...
How to develop nrf31512, is it same to the nrf24le1? why i use the same firmware download to the Nrf24le1, it can run normally, but download to the nrf31512 , it can't work...
Hi All,
In my application I have two analog inputs coming from two different sources that I have to sample using one SAADC present inside NRF52. As far as I know, NRF52...
Hi,
I'm using nRF5 SDK V12.0, I found a strange problem. That is the UART can send data to PC, but it cann't receive data from PC. However, this problem just arise on some...
Hi,
I need a bit of help to fully understand how ADC works on nRF52832.
I am using a Thermistor sensor like the following to measure temperature:
Epoxy Thermistor...
We would like to use the PPK for automating some of our tests. Is there any documentation on how to drive the PPK over RTT? If push really comes to shove, we can always read...
BLE UART This is a problem that I have discovered while checking
the cause of the connection frequently due to communication error.
It is normal... In the nRF52832,...
Hi,
I added following code in saadc example code to set GPIO pin high/low and monitor it in the terminal. The pull up looks ok, but when I set it to low, the reading never...
We created our own PCB for the NRF52 with a Johanson chip antenna but no matter what we do, we can't get a signal from the Antenna, not even a weak one to show up on the spectrum...
Hello,
I duplicated the project example "nrf51-micro-esb-master" under "proprietary_rf" and got it up and running. I now need to incorporate some timer functionality.
...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
As I've tested by using
err_code = sd_ble_gap_address_get(p_addr);
APP_ERROR_CHECK(err_code);
App returns...
hi
i am using nrf51822. i used the radio tranceiver example and it works well. I am planning to advertise the received packets so that the range can also be increased and...
Hi all --
I have a tricky layout "issue" where unfortunately, I've ended up connecting my I2C device to the BlueTooth module on the side of the module where my VDD isn...
