I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hi,
This seems to be an issue that pops up often. However, I wasn't able to find an answer here in the Nordic forum.
What I have:
a number of vendor services ...
I'm trying to change the SD version number of a test-S132-file, soI can "see" that the DFU was successful in my app. I can already read the current version (from 0x300C in...
Does anyone had controlled LoRa module with nRF5x??
I have nRF51822(BLE400(PCA10001)), nRF52832(PCA10040) and Semtch SX1276RF1JAS.
I hope to control LoRa module using nRF...
Hello All,
I am looking for a stand alone small transmitter/receiver that can be powered from a watch battery with a range of at least 300m. Is any of the nordic solutions...
hi,
i am working on code which require to store data array of 20x20 to store in flash area using FDS or any other possibilities.
1)i confused with FDS concept. how i can...
Hi,
we are now in the second round of prototyping - we'd like to move away from the chip-antenna based design to a PCB antenna. We have come up with two different ideas...
Here
My device (chip nrf51822_xxAA) exist softdevice 8.0.3 and BLE uart application work fine which flash by the ST-link in Keil MDK(5.20).
Now I try to add bootloader to...
Hello
I've found your example in the dev-zone and migrate the project to SDK10 and will probably do the same for SDK11.
However, I've got a problem in my project. When...
hi,
i want to implement rtxos in my nrf52832 application. one of the nrf52832's feature is ARM Cortex -M4 32-bit processor with FPU, 64 MHz.
my question is, why the...
Dear Nordic.
I am developing bootloader without SD (s120_nrf51822_1.0.1).
And after execution of bootloader, jump to application working with SD.
Flash composed like...
I tried to compile blinky sample in SDK12 with make tool-chain. I got 3 errors:
Makefile:214: Cannot find include folder: ../../../config/blinky_pca10040_s132
Makefile...
I converted a project from uVIsion to IAR, and I get an error when I use app_timer_start(); the error says: Error[Pe167]: argument of type "void ( )(void)" is incompatible...
I don't need to connect the master with the peripherals, but i have to know how is the maximun quantity of scan response that can accept the master.
In the example ble_app_multilink_central...
In trying to move to SDK 12.0.0 from 10.0.0 I get the error:
"...components/includes/app_error.h:33:23: fatal error: ant_error.h: No such file or directory
#include "ant_error...
Hi,
I want to run BLE mesh network example on my Dev board to understand it better.
I am running it on SDK v8.1 and using ble_app_proximity example S130.
Following...
