Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
in the NRF52832 documentation the TX chain delay is 0.6 µs while the RX chain delay is 9.4µs.
Does that mean if transmitting two packets in a row to the same receiver...
Hello everyone,
I have been using nrf52 IoT SDK for MQTT implementation. Everything works fine as long as I am publishing or receiving only one character i.e.
param...
In Bluetooth Spec (CoreV5.0, Vol6, Chepter6, Section1) it is mentioned that the random private address is generated periodically by a timer handler. I could not find any mention...
1.specification says that we should trigger EP0STATUS task to initiate the status stage for control transfer(read/write).
actually nrf52840 will auto ack the OUT TOKEN...
In Eddystone example in SDK 12.2.0, APP_MAX_ADV_SLOTS parameter is by default 5, but if I try to use less than 5, an error appears in es_flash.c because in the code, 5 slots...
hello there i want to scan particular device. so i am using whitelist. i change in hear_rate center code. but its not working. other unwanted devices are also scanned. i am...
Hi,
We are working with the nrf51822 on mBed platform
We have created the following profile under deviceinformationservices
in main.c
uint8_t DataCounter = 100;...
Hi there!
I found out that there is some problem in the example ble_app_hrs_rscs_relay in nRF5_SDK_11.0.0_89a8197. I want to restart advertising when adv timeout. I did as...
I'm trying to use app_timer_cnt_get() to implement an RTC Calendar system on a Gigawit module (nRF51822).
I have a test app_timer that has presacler=0 and period=3 seconds...
This is no a question, but i was not sure where to post it.
I was trying to use the nrfjprog command with the new version of SEGGER JLink, but the terminal output was ...
Hi! I'm trying to work with the beacon kit, but I have some confusion about which type of sdk I can use because with some example that I have found it doesn't work.
Besides...
When i use ble_app_hrs to connect with hrs demo(ble_app_hrs example), everything is ok.But when i connect to a heart rate monitor, it always disconnect.The print information...
I try to stop the advertising by using ble_advertising_start(BLE_ADV_MODE_IDLE) when the advertising is ongoing. It fails.
Please tell me how to stop advertising when the...
I have a problem where a central device (iPad) has to connect to a peripheral (running nrf51822, s110) as quickly as possible, receive data and disconnect again.
Right...
