When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
I am still noticing a higher than expected power draw on my nRF52 and I want to make sure I have adopted best practice in turning things off/optimising things before entering...
Hi,
I am using a 128KB-rom 16KB-ram nrf51822 and trying to run blinky from SDK 11 with softdevice.
If I load nrf51 S130 1.0.0 softdevice, and use the following in my...
As of SDKV12, because of the removal of pstorage, I upgraded my app to use fstorage.
If you look at the SDKV12 doc at this link, you will notice that it is quite lacking...
Hi,
I am trying to write some data into the flash of the nRF52832 SoC, but can only write around 5 kb of data. After that I will get an error of number 7, which should...
I'm using SDK v11, nRF51
I started developing with S130, v2.0.1
The device is peripheral only, so I decided to switch to S110 v8.0.0, since I need the memory.
I made...
I don't have a particular issue right now, just a concern that I have because my device needs to be bulletproof when it comes to reset behavior.
When sd_mbr_command(SD_MBR_COMMAND_INIT_SD...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
Hello,
I'm developing nRF52 with Keil5.14.
Before I used nRF52_SDK_0.9.2 and it worked fine.(With NordicSemiconductor.nRF_DeviceFamilyPack.8.0.3.pack)
I upgrade the...
Hi all
According to the following post, the RAMONB register doesn't exist since the nRF51822 has only 2 RAM blocks: devzone.nordicsemi.com/.../
But the current version...
Hi, i use the SDK11 and i will send and receive beacon and be able to launch a BLE DFU.
I am able to make a software in wich i can receive and send BEACON but in...
I'm trying to upload via DFU from one nRF51822 to another nRF51822 via DFU
The receiving side is not a problem as there there are loads of examples.
But I can't find...
Hi,
I'm developing some code for an AVR MCU with the Adafruit nrf8001 and had a question about the expected behavior of the handshaking lines, REQN and RDYN
My understanding...
