We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hello Guys
I'm currently working on a BLE AoA (Angle of Arrival) application using the nRF52833 Development Kit . I’ve run into some challenges regarding hardware connectivity...
Hello ,
I am doing a new Keil project to run concurrently ANT for messagging exchange and Bluetooth LE for advertising.
On KEIL pack Installer I cannot find the example...
I want to implement the OTA update in nRF51822 on my custom board. I am using the bootloader example in the dfu folder for this. When I try this code on the DK, it works fine...
I am using nrf51822 with PCA 10001, SoftDevice S110 8.0.1. I try to compile the example "ble_app_proximity_s110_pca10028" and after I made a connection the device disconnects...
Has anybody had any experience in programming an nRF beacon kit over the air using the built-in Bluetooth Smart interface in a Windoze 8 laptop? (HP 255 G3) Is this even possible...
Hi,
I wanted to create fixed rate waveform. I first used nrf_delay_us with nrf_gpio_pin_toggle. But I realized it is not accurate enough to do it, especially when the device...
Hello,
I'd like to know how exactly do i implement this function in my app?
I tried getting the value from response (as shown in documentation) : ble_gattc_evt_char_val_by_uuid_read_rsp_t...
Hi,
My Jlink lite CortexM work with nrf51822 DK boards. But my PCB with nrf51822_xxAA chip can't download code. I'm using ukeil
When I chek in utilities Jlink can't recognize...
I am initializing an SPI master to talk to ADXL362 accelerometer using NRF51-DK.
Datasheet page 19: www.analog.com/.../ADXL362.pdf
No matter what I do connected or disconnected...
Hello,
I am new to working with imbedded chips and could use some help. I am working with a pre-programed nRF51822 chip on a PCB and would like to be able to read the imbedded...
Hi I want to using nRF51822 link with MCU ti-am335x have Linux system(Ubuntu) by standard HCI command, BlueZ or related hci tool.
I know that I can use nRF51822 S120 serialization...
I would like to share my wireshark capture file (pcapng) with another developer to view that doesn't have a nordic sniffer. They cannot see the ble protocol information. Is...
I am able to set the connection timeout to 250ms in the ble_app_hrs peripheral sample, but in the ble_app_multilink_peripheral it will not advertise if I set it below 1000ms...
Hello,
When using the bootloader I've noticed that the booatloder resets after advertising for ~1minute. I'm try to figure out if this is intentional.
I notice that...
Hello,
I am currently designing a project that will advertise as two different beacons simultaneously using the Timeslot API. I have successfully implemented the nRF51...
