I've been working on a custom device utilising the nRF52832 that needs to switch GPIOs in tightly controlled pulses. The problematic section is part of a much larger project...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
hi Guys pls HELPPPPP
I have developing active rfID tag using nrf24L01+ and ATtinny13A, the program code is done perfectly, firstly I start developing the tag with separate...
Issue is related to:
devzone.nordicsemi.com/.../
Now I use latest SD S130_1.0
So, I added to my service characteristic with notifications enabled. But during discovering...
Hello,
I have a development kit with the PCA10000 and I can comunicate with the PCA10004 for about 5/6 meters what is ok for my application but now I want to comunicate...
Recently I needed to add some functionality, so the software could monitor when there was a ble gatt read characteristic event.
In the addCharacteristic code I simply set...
Hi, We have used nRF51 DK for developing an application where we used USB to load/flash the program code. Now we are in Pre-production stage where we can use only the nRF51422...
Hi,
I would like to extend the HTS service with measurement interval setting support. Bluetooth SIG specifies the measurement interval characteristic, which is easy to...
I'm using the example ble_app_hrs along with the HRM part of the nRF Toolbox iOS app . It makes sense to handle this in on_ble_evt in main.c but am unclear how I can recover...
Hi Team,
I am testing UART on nRF51 DK kit.
I have flashed uart_pca10028 .
I have taken out jumpers from P0.9(TX), P0.11(RX) and GND and connected to PC com port.
...
I have the example app working nicely now, so I want to export the project to a zip or something, effectively copy it, and put it elsewhere in my filesystem and work with...
Hi,
I tried installing the kernel (raspbian-kernel-zip Raspbian kernel for Raspberry Pi 3.17.4 ) on a Raspberry Pi 2 (Model B 1 GB). I found out that the Pi doesn't boot...
I'm trying the multilink central example with s120 and SDK 7.2 (because of simple_uart).
However, my PCA10028 board gets stuck at this macro:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
My code is attached but essentially it is saying that SPI_MASTER_0 is not defined when I compile. I have the line:
#define SPI_MASTER_0_ENABLE /**< Enable SPI_MASTER_0...
I'm trying to get the ble_app_hrs working on PCA100001, the software installation is brand new (all installed today). I modified the pca100028 ble_app_hrs to try work with...
Hello everyone,
I have problems with my nRF51822. I think it is related to the starting memory address of softdevice. I attach 2 nRFgo's screenshots.
I have programmed...
