nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
I have an nRF51822 board that is running fine for a while. At some point, it runs into an error and calls ble_debug_assert_handler() and goes into an infinite loop. At that...
Hi all,
I am new to nRF51822,now I want to used a simple ble application to send a data,and nRF51822 ble device read this data to control RC servo motor ,for example app...
We are using S130 v0.9 stack,
and when BLE device A is connected as peripheral of iphone
and central of BLE device B at the same time
iPhone --> A ---> B
Device...
Hello,
I am working with the nRF DK trying to read a sensor over I2C. I wrote some code in Keil uVision and I finally could read the sensor. The problem now is, for some...
I encountered a strange problem system reset. My application runs on iOS or android. My device was connected by iPhone 6 plus(128G) with iOS 8.1.2. ANCS was turned on. I have...
Hello Everyone
I want to implement TWI interface in my project.Presently I am using Keil UV5 IDE, PCA10028 Development board and s110 7.1.0 softdevice, along with that...
Hi,
So am new to all this BLE stuff, I have been using the nRF24L01 modules but want to move to the BLE variant, nRF51822.
I am these days figuring out the toolchain...
Hi,
I am developing on a nrf51822 based board using s110 softdevice v. 6.0.0.
In my program I need to change the bluetooth GAP device name in runtime
during connection...
Hi,
I compiled the nrf_heart_rate_collector. Apparently, this program only works once, between each run, "remote device" and USB dongle has to be resetted (unplugged from...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi ,
I am trying to set up event using GPIOTE. I want to implement reading of sensor data and sending over BLE when an interrupt is generated due to activity on a particular...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
Hello,
I try to add the Device Name to the ble_app_beacon example but it does not work.
First, define the Name:
#define DEVICE_NAME "MyBeacon"
Next, add GAP Pararameters...
First, many thanks for the great DFU recipe in the latest SDK!
I've ported OTA DFU to the IAR tool chain for both s110 and s310. I can flip back and forth between the two...
