Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi,
I'm designing a wearable, low power inertial and EMG system and have to choose between using ANT+ or BLE with the Nrf51422 on my own board.
The system would simply...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
I need to automate updating the bootloader and radio for an nRF51 in a production setting with a VB.NET windows application. I'm able to call dfu/main.py with the code below...
Hello,
Just uVision 5.14 and SDK 7.2.0. Try to compile the blinky example and get the next error
._build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol nrf_delay_us...
Hello,
is it possible to get the schedule that is used internally to communicate with connected BLE devices? I have a bunch of data that I want to send to connected nodes...
Hello everybody...
I am new to nordic development tools. I wanted to develop a ble application on the nRF51822 development kit. I am struggling to figure out how to set up...
Hi All,
I am using s110 v7 soft device , and SDK: 6.1.
I have implemented static passkey based pairing.
I would like to terminate the connection if central unable to sends...
Hi I am using the RBC mesh " github.com/.../nRF51-ble-bcast-mesh" , sd_110_7.1 and sdk_6.2
The rbc mesh is using timer0 as well as the softdevice. I removed the app timers...
Hi all,
we are performing some transmitter spectrum measurements using your nRFGo (PCA10005) board and an Aaronia HF-60105 spectrum analyzer.
The SMA connector of nRFGo...
i have nrf518822 device..i downloaded s130 soft-device from nordic website..i have installed keil 5.0 and nrf go stuidio....now tell me how to flash soft device and application...
if i use s130 soft device will it do simultaneous master/slave role.....
c1=central 1,c/p=centarl/peripheral,p1=peripheral..
assume c/p made a connection with p1 and it...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
I have an ANT device, that on a button press, it must wake up, connect to an ANT channel, and send a...
Hi all,
I am trying to connect a tablette (s110 peripheral role) to 5 S120 centrals simultaneously.
I am using nrf51822, sdk6.1, s110 v7.0, s120 v1.0.1 .
Is this possible...
So I've seen all similar issues people had where their program stuck on sd_softdevice_enable() due to the fact that ran on custom boards which didn't have external oscillators...
