I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I'm following the example here for the PCA10028, only the example I copied from the Pack Installer is called ble_app_hrs_s110_dfu_experimental_pca10028 (nRF51 PCA10028) instead...
Hi, I am studying with nRF51822 (s110).
I found some source code from devzone.nordicsemi.com/.../
and I am trying to change the device name,
And I don't know why...
I am trying to integrate BLE into my wireless heart rate monitor project with an Arduino Uno.
Everything works and can successfully be exported over a different BT antenna...
nRF Master Control Panel on LG G2 with Android 4.4.2 can't connect to S130 v0.9 with example that goes with SoftDevice.
But it can connect to S110 example that goes with...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hi,
Does anyone know if ESB example library has LBT implemented?
Been doing a timming mapping between master and slave on packet exchange, and looks like a bit too exact...
Hi,
1- Many MCUs, including NRF9E5, have specialized communication ports like UART or SPI. Why not I2C? I assume that every pin can be programmed for any communication...
Hello,
I reckon that it is not possible to write application logic that decides whether to answer a connectable advertisement packet with a connection request as soon as...
I am using the nrf51822 with sdk (6.1.0) and s110 (7.1.0).
Can I do this?
If the nrf51822 is advertising, do Smartphone search the nrf51822?
Or do the ads on My smartphone...
Hello,
In the following code, I have tried to assign a channel to be asychronous so that I can transmit 8 byte acknowledged messages immediately following a button press...
Hi Support team,
I've ported succesfully chibios RTOS on the nrf51422 for month. I've also ported some drivers like I2C - UART - SPI- GPIOS and others... I can play with...
Hi, I have the nrf6310 code in C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310\s110 and then i need use this code in the board PCA20006 (Smart beacon).
Do you know how...
hello Nordics,
i am trying to configure 1ms timer along with BLE_STACK is enable
and same time i am sending 3byte data for every 500ms . and 1ms timer is very important...
I need to automate OTA updating the bootloader and radio for several hundred units that have an nRF51 (softdevice 7.1.0) from a VB.NET windows application. I'm able to call...
