Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
hi,
i am using uart example from nrf51822 example. when i am sending continuous stream of data then my connection breaks. it disconnects from peripheral device.
how should...
Hello
The nRF51822 has as I understand it 256kByte flash and 16kByte SRAM.
If I run the S110 softdevice, how much sram/flash memory is available to my application program...
Hello all is there a way to have the nRF51822 report back UTC in nano seconds, my though on this is the basic RSSI does not really tell the distance correctly I would like...
HI,
so i designed my board based on the NRF51822-QFAC chip. here's the link of the nrf : www.digikey.com/.../5125206
and find attached the schema of the BOARD that...
Hello,
I have some communication overflows on UART on nRF52, SDK 11 alpha, DMA active, big buffers (1024 bytes). I don't understand, nRF52 is not blocked in an interrupt...
When I am trying to use that file for Firmware Over the Air update feature in my application code then program compilation and all is working fine but when I am trying to...
hi all,
i have a electronic device having a button which sends continous data till i keep button pressed.
i want to send these data without losing connection.
i can across...
Hello,
I program the nrf51 in C++ using GCC and Eclipse as IDE (this question is not related to the C++ toolchain).
I was wondering if it is possible to add the extern...
Hello!
I bought NFR52 DK preview board. As microcontroller it works well. But when I try BLE examples, they do not work. I installed SoftDevice S132, downloaded ble_app_uart_s132_pca10036...
Hello!
I want to add the battery services in my nRF51822 project for getting the message of battery. Is there need battery-powered?
But,I am sorry to see that the led which...
hi everybody,
I'm working in a project, I need to establish a connection between a beacon & the mobile phone, I want to prevent any other masters of connection to my beacon...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hi new to Bluetooth, but familiar with Radios and embedded devices
I have 2 devices that only connect to each other.
in the interest of extreme battery conservation I...
I am using a BLE UART friend module and I am trying to set the GAPIntervals parameters. I realised that when I set my max conn interval parameter above 2000ms, the device...
