Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hello,
I am developping an application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) extended advertising on SDK 2.7.0.
costum chip nrf52840 (on...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello,
in our final device, I want to give the user the opportunity, to close an opened BLE connection between our device and another smart device. This should be done...
I have 2 boards. The first board, I run the demo project code for ESB PTX. And it works fine. However, I load the same code on a second board, and "nrf_esb_enable()" never...
I intend to use ESB to transmit data every a few hours. Since I want to use a beacon board, I assume the ESB app needs to sit on the S110 softdevice.
I added S110 to the...
Hello.
I use nRF51-DK and need to avoid appearing of the virtual drive during connection to PC (it's confusing my customers). So, I want a behavior as an old PCA10001:...
I am designing with the nRF51822 and I have a choice of either a 32Khz or 16MHz crystal. Can you tell me the advantages and disadvantages of both?
If the 32KHz crystal...
Hi,
I've got a question about the startup-process and power consumption using BLE&Advertising (sample code: nrf51-ble-tutorial-advertising )
I've got the "new" nrf51...
I would like to see app_trace_log messages on a terminal window on my PC.
I did the following things:
Added the define ENABLE_DEBUG_LOG_SUPPORT to my project in the...
Hello,
When I set min to 7.5 ms and max to 200 ms. Witch one is used at beginning (it looks like if it was max) ? Do transitions are done automatically depending on numbers...
The V3 S310 documentation appears to show that it can operate in a Central Role.
The BLE_GAP_SVCS enum has been modified to now include the following additional values
...
Hello,
I'll explain my project.
I developed a device that take a magnetism sample (with a sensor) each hour, but the device should be available all the time, because...
Hi,
I want to have a bootloader without softdevice on SDK 8.1.0
I do not want to change the SDK and it seems to me the SDK only works with softdevice.
Do you have such...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
i am work in ipv6 coap Server example.
in main function pstorage_store/pstorage_update work well....
sdonly.zip softdevice.zip Custom board with a nRF51422, SD 310 rev 2.0.0, nRF Toolbox rev 2.4, iOS 8.4
When trying to use the DFU app to update my softdevice and/or the...