Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi, the title says it all really. I'd love to get my hands on a sample application from the Nordic github repo (or elsewhere) which shows clearly how to implement for S110...
I've read the document, 51822 Product Specification 3.1
But I can't find which pins are assigned for SPIS.
I'm using QFN type.
Directly speaking, can I achieve SPIS...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
in our final device, I want to give the user the opportunity, to close an opened BLE connection between our device and another smart device. This should be done...
I have 2 boards. The first board, I run the demo project code for ESB PTX. And it works fine. However, I load the same code on a second board, and "nrf_esb_enable()" never...
I intend to use ESB to transmit data every a few hours. Since I want to use a beacon board, I assume the ESB app needs to sit on the S110 softdevice.
I added S110 to the...
Hello.
I use nRF51-DK and need to avoid appearing of the virtual drive during connection to PC (it's confusing my customers). So, I want a behavior as an old PCA10001:...
I am designing with the nRF51822 and I have a choice of either a 32Khz or 16MHz crystal. Can you tell me the advantages and disadvantages of both?
If the 32KHz crystal...
Hi,
I've got a question about the startup-process and power consumption using BLE&Advertising (sample code: nrf51-ble-tutorial-advertising )
I've got the "new" nrf51...
I would like to see app_trace_log messages on a terminal window on my PC.
I did the following things:
Added the define ENABLE_DEBUG_LOG_SUPPORT to my project in the...
Hello,
When I set min to 7.5 ms and max to 200 ms. Witch one is used at beginning (it looks like if it was max) ? Do transitions are done automatically depending on numbers...
The V3 S310 documentation appears to show that it can operate in a Central Role.
The BLE_GAP_SVCS enum has been modified to now include the following additional values
...
Hello,
I'll explain my project.
I developed a device that take a magnetism sample (with a sensor) each hour, but the device should be available all the time, because...
Hi,
I want to have a bootloader without softdevice on SDK 8.1.0
I do not want to change the SDK and it seems to me the SDK only works with softdevice.
Do you have such...
