Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Where can I find the BLE_GAP_EVT_ADV_REPORT value if I am using S310 SoftDevice?
Without it I cannot use my client to get advertising data from server. Or is there any other...
Hi Nordic：
I have two questions about SoftDevice s130：
Device A,B,C,D are using s130.
When this device (called A) is a peripheral and connected with a tablet...
Dear Nordic developers!
I am working on a project, which should use the ANT+ and the BLE communications, too. The S310 SoftDevice is good for them, but I have some problem...
Hi
I have been reading a lot of posts and the documentation on DFU for SDK7.2, but something is not really clear to me.
When I compile and program the boot loader in my...
Has anyone added an external power amplifier to the nRF24L01?. For my application, I need to increase rf power.
What about a skywork Amplifier ? if there is any amplifier...
Howdy all,
Has anyone added an external power amplifier to the nRF51822? From what I recall the BLE spec allows for 10mW output power (well, 10mW would be the maximum for...
Is there any recommended chip antenna for NRF52 SoC? Any guideline on the antenna placement, designing the matching circuit etc? I assume for NRF52, no need for an external...
I have moved bootloader from 8.0.0 SDK on top of our custom application. During boot, the softDevice transitions to bootloader as expected. The bootloader then advertises...
I'm using vanilla version of the dfu_dual_bank_ble_s110 project on top of my application. The problem is that the firmware enters bootloader mode whenever a USB is connected...
Is there a way to figure out for which target a binary in _build/ is compiled with Keil?
(other than parse .map or .lnp file for a file unique to the target)
hi , I am trying to download the softdevice(v8) and cross compiled application(using makefile in nrf51822 sdk v6) from my Linux PC using JLinkExe.
following is the memory...
if i am a master i want know to know the sleep period of node,how do i know...?
how do i know whether it is sleeping or awake..?
if i have data to sent for node,but...
nrf51822_AA rev3, SDK8.0.0, S110 8.0.0
My application has the max number of bonds set to 24 with a size of 128bytes each. So that's 3 pages. Plus one page for saving user...
