Hi......
the board advertising correct,and it work normal (connect,send and receive data),bug it's name can not display in app scan menu. the definition is "liu",but displaying...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Looking at the ADC HAL, I see 8 choices for ADC input, plus a disabled case. Is it possible to choose as the input to the ADC a node that is proportional to the VCC battery...
We're building a low cost device with an nRF8001 as the only means of communication as physical access is closed after the device is built.
Is there any way to change the...
Hi Guys,
I would like to set up my nrf51822 to make a connection once a GPIO button is pressed and send some data. I've been using this sheet to try and calculate what...
Hello,
I've purchased 2xnRF905-EVBOARD
I made some test with a spectrum analyzer. The output of the module is nearly 10dBm as mentioned in the datasheet.
I connect the...
I'm using PCA10028,SDK9.0,S130.I want to set and get the ble address,but I found that couldn't get the ble address by using API sd_ble_gap_address_get,the chip will reset...
Hi, there! Does peripheral with ANCS only be connected by iOS? I ran the ANCS demo in sdk 9.0, and it works well with iOS. Once an Android phone connect to it, it was connected...
On developer site I saw "The RSSI value of the beacon measured at 1 meter distance, which can be used for estimating the distance from the beacon." I don't get it can any...
I am using HID service over GATT and have several reports defined. When I increase my report map data size by adding more reports, my map size is 280 bytes, whihc seems to...
I want to try the nRF Sniffer app but that requires that I reprogram my nRF51 dongle. I want to know that I can restore it before I do this. I can't save the current "as-shipped...
Hello,
We recently received an eval kit the the nRF52832, but we were told not to take current measurements with this version. This presents a problem since we are evaluating...
Hi all,
I'm using two nRF51 DK to measure ADC input on peripheral side and translate it to central, based on Multilink example.
One software timer is used to perform one...
good work.
I will have a question for you .
I think to make the connection and the connection I made adxl345 nrf51822 and LCD screen x, y and z coordinates , I want to show...
I use sdk 9.0.0, softdevice s130, nrf51422_xxac. In my application I have to both scan and advertise. When I start one of them (scanning or advertising) application starts...
Hello everybody,
I'm trying to use the RTC1 in the LedButtonDemo, in order to blink the led once we put 01 in with the Master Control Panel on my computer, but all my tempos...
Hi I need to test serialization with Nordic , since I need to use it for my application..
I want to first try it with my Linux Laptop. i.e, Connect NRF51822 to my PC using...
