Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
We are trying to integrate an accelerator driver with the code written in c++ with example code from twi sensor from the SDK 0.10 for the nRF51, which is written in c. Will...
Hi,
I am struck with the problem of GAT ERROR when I upload my application zip file through Nordic nRD ToolBox in Android.
These are my steps:
I load the S310...
I recently migrate to SDK 10 from SDK 9 and printf is behaving weird with baud rate of 92100 (460800 and below works fine). Some of the characters were printed out of order...
Hi,
I am trying to implement some custom services in PCA10028 version 1.1.0 with Android, I am following same code which is in github ( github.com/NordicSemiconductor) it...
Hi. I try to nus + pwm.. I am using github.com/.../nrf51-pwm-library ..
When I combine 'ble_app_template' + nrf_pwm, it works fine.. but 'ble_app_uart' + nrf_pwm is not work...
Hi Guys,
I am working on nrf51822.
I use the nrf51-ble-app-temp example with "nRF Temp 2.0 for BLE" APP.
But it is not work.
Anybody workable with "nRF Temp 2...
Hi
Is it necessary to certify a new product for CE compliance if we use a reference layout as a base for our design? In particular, we want to design a USB dongle using...
Hi,
we are using a nRF51822 built into an industrial sensor device. As part of the final production test we want to check the RF connection between the BLE chip and a test...
Hi,
I have a central device and I need to register lot of 128 bit vendor service/characteristics (~20).
However, sd_ble_uuid_vs_add return NRF_ERROR_NO_MEM.
Some post...
HI , Global Tech Tour 2015 - Shenzhen I get the infomation that the R&D in nordic Semiconductor has got the development board NRF52 smart remote. What's the data you will...
Hi All, I'm trying to compile and download sample code "dual_bank_ble_s130".
But it seems fail to run.
I'm using SDK10 examples\dfu\bootloader\pca10028\dual_bank_ble_s130...
can we transmit data of size greater than 40kb (image) through nrf51822 but without connection to peripheral device i am working so hard to find a way but not achieving the...
Hi I'm trying to optimize my connection interval for latency vs power consumption but I notice that a lot of values I try to set are giving me the invalid parameter error...
Hello,
I am using S120 central stack 2.1.0 with SDK 9.0 and able to work with single server connection. Now I am trying to connect to 2 peripherals with 2 different UUID...
I read timer example of SDK7.0/6.0, and found that often we write some code to tigger the clock.
but the same example of SDK9.0 needn't. why ?
the code of SDK7.0: NRF_CLOCK...