Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
I'm using nRF52832 SDK board with softdevice s132_nrf52_5.0.0. The error appears when I try to load it to the board, right on line 1247 where it initializes the NUS service...
I see that a Serial LTE Modem sample application is in progress in the master branch...
I tried master in the commit: a955d411
Once on that commit I did update (west update...
I can't get flashlog/crashlog to work properly. The symptoms are that when NRF_LOG_BACKEND_FLASH_START_PAGE is set to 0 (i.e logs are written to address right after the application...
I have a nRF528420 [on Skylab module SKB501] and have wired up a custom connection to USB. I'm able to program NRF52 with both softdevice S140 and BLE Peripheral ble_app_uart...
Hello,
I try to add watchdog on aws_fota sample but Something is wrong about bootloader to application transition and it always reboots.
00> [00:00:00.051,513] <inf> mcuboot...
Hello everyone,
I have found the following issue in the behavior of the SPI driver:
having connected an NRF52840 as an SPI master which is set to receive 22 bytes from...
My peripheral uses "LongWrite". Communication with Central has been successful. I want to know the length of the written data. After trying the following, the obtained result...
I’ve been developing the FW for an nRF52832-based module that controls a simple lighting product.
The capabilities include support for secure DFU and a modified version...
Target : NRF52832 as Server
Description of the problem (seen in wireshark)
Client : write request (0x12)
Server: Rcvd Error Response - Invalide Attribute value length...
We're porting an nRFS52832 app from an earlier version (14) to 15.2. Using sd_ble_gap_device_name_set( &secMode, dN, len ) with a string of length=9 will only show 5 chars...
Hi, we are trying to get the nRF9160 connected to the internet again, we had it working 6 months ago.
Our hardware is 0.8.5
We are in Ireland where we only have NB-IOT...
Hi
I'm using the watchdog of the nRF52832 Rev. 1.
The PS V1.4 states that the maximum run current of the watchdog is 2uA while the typical current is only 0.3uA. Can you...
Hi,
I am migrating from SDK14.2 to SDK15.0 and I can compile now, but when runnning the nrfx_uart_init the hardware handshake signal RTS is high from the beginning.
...
I am running into compile errors in different places in the SDK where there are lines as shown below: #if (NRF_BLE_GATT_ENABLED) /* do something */ #endif It is a widely and...
