Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello!
I have 18-bit sensors with SPI and I2C , which I intend to use in a wireless array.
I need to choose equipment and topology (star, scanning mode?), enabling data...
We had a custom board made with the nrf9160 and I noticed I was having trouble communicating with the sim card on my board.
We have been testing i2c, spi, number of peripherals...
I am trying to run the hci_uart sample on my 9160 DK but I am facing problems uploading the code. I am able to run the AT client and Asset tracker just fine. As soon as I...
I've been attempting to optimize my scan and connection intervals in order to maintain the highest percentage of time scanning while maintaining connections, following the...
Hi,
I am developing a Linux PC application (central) connecting with nrf52840 dongle with s140 v7 flashed on it (for long range support). I am using pc-ble-driver v4.1.1...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
I have 3 devices that can communicate via UART: 1) nRF52840-DK (PCA10056) 2) FTDI (set to 5v logic) 3) BLE HM-19
I'm using the example in ./nRF5_SDK_16/nRF5SDK160098a08e2...
Hi,
In gps sample, the prj.conf file is:
And I can use Putty or Serial.app (on my Mac) to view the output
In our application the prj.conf file is the following:
...
nrfjprog is reporting "Cannot connect to J-Link." while trying to erase on MacOS Catalina
Board used to work properly, but attempting to re-connect after a wipe of my MacBook...
I am using the nRF52840 dongle (pca1009).
I have read from some digital inputs successfully, but am not able to read from P0.02.
I set it up as an input with the following...
I am new to BLE and this question may seems little unusual.
My goal is to connect two nrf52 together over BLE and when i press a button in central device , a write event...
Hi!
My goal is to sample an ADC channel with 10 kHz sampling rate and acquire 2000 samples in one samples acquistion and then return to lowest possible power state. This...
Hi,
I received a Thingy91 from a colleague who orderd it shortly after hitting the virtual stores but didn't do a lot with it. I got it on my table and started to work on...
Hello,
SDK 15.3.0
s140
nrf52840-DK
IDE: SES
I am attempting to use the LPComp + NRFX TIMER 4 to count the rising edge of a signal, the timer is being used to time...
I am currently evaluating the nrf52840 for a possible future application which is based around BLE and should also provide a HID Generic interface to perform communication...
