I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
I was checking DFU through serial usb/uart on the following link:
infocenter.nordicsemi.com/index.jsp
I want to double check if this entire project is for programming...
Hi,
While linking I am getting the following error on Nordic SDK 16.0,
XYZ.axf: Error: L6218E: Undefined symbol nrf_ble_gq_conn_handle_register (referred from ble_db_discovery...
Hi everyone,
I am new to segger embedded studio. I want ibeacon firmware sample code to advertise uuid, major, minor, tx power, advertisement interval. I want to change...
We're developing a product where a single NRF52840 board - lets call it the central- serves as the focal point for multiple NRF52840 boards spread out across an area - lets...
I am not able understand the difference between APPROTECT and BPROT . Can you please clarify ? and if we enable the protection then how to disable it again whenever we want...
I've seen many posts about LL_LENGTH_REQ causing disconnection on certain Android phones and the solution from Nordic is to add a 100ms delay. Can someone from Nordic definitively...
Hi community,
in our setup we use the LSM6DSL IMU using TWI. First we initialize the TWI peripheral, then we configure the IMU. After that we initialize PPI to automatically...
I am trying to build the project "thingysdkv210" which is downloaded from https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms/Nordic-Thingy-52/Download#infotabs...
nRF52 DK
HTS example
I added app_timer_stop_all() in the ble_evt_handler() of main.c, under the case of BLE_GAP_EVT_DISCONNECTED, but the battery service timer still...
need help on multiple things
All work is on the DK 840 board using sdk15.3
Started with this link
https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic...
Is it possible to run the Zigbee Light Switch example with the internal RC.?
On the sdk_config.h I have changed the following:
#define NRFX_CLOCK_CONFIG_LF_SRC 0
But...
In the only example in SDK16.0.0 with soft_device and Free RTOS, configMAX_PRIORITIES is set to 3, which means available priorities 0,1 and 2.
Is it possible to change configMAX_PRIORITIES...
Hi i'm very new in using Nordic nRF52840. Got 2 questions:
1.Why does each example project contain blank/mbr/slxxx folders? in these folders they all have a copy of the...
