Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi all,
I am working with SDK 15.3 (S140 6.10) on ISP1807, which is nRF52840 based.
For my application I needed a USB dongle which works as BLE Central. It is supposed...
Hi all:
Currently, when using nRF52840 for archiving applications, I will encounter a condition and this will result in data corruption.
And I found a way to reproduce...
Hello,
I'm having a bit of difficulty disabling the PWM peripheral when it is no longer required. From the manual it states that "To completely stop the PWM generation and...
I have a custom BMD-350 board with a UART service. The board connects just fine with the nRF Toolbox iOS app but does not work with the Android app. The app connects to the...
Hi,
I am a little bit confused about the different supported stack for the nRF52833 when using BLE Mesh. With the current example, there is only support for the S113. Can...
I started a timer on the nrf52840 and the SDK is nRF5_SDK_15.2.0_9412b96, but I haven't never receive the callback message after the time. What's the reason?The code is as...
Hello ,
In this scenario, I have to measure the time interval between the START and STOP pulses generated by a peripheral device connected to nRF52 DK. The thing is START...
Hello!
I am currently using a module called BLENano2 (nRF52832). SDK15.0.0 is used and the editor is "Segger Embedded Studio v4.16".
Finished writing the program that...
Hi,
I tried out the light switch example on a nRF52833 and it seems not to be reliable at all. So i connected the debugger and saw, that in access.c,
in packet_alloc_and_tx...
Hi all,
I am trying to use nrf52840 dongle as hci_usb with the very simple task: scan
Host is Raspberry Pi with BlueZ
Controller is nrf52840 dongle with firmware hci_usb...
Hi
I want to move DFU at the application level. Is this possible? I want to move DFU at the application level because of my project requirement.
1. In my project, I have...
Hi, I am trying to get the BLE values on Thingy91 (PCA20035) . And I have followed the
devzone.nordicsemi.com/.../217018 I have ported the diff (nrf and zephyr diffs from...
I am using built-in DTLS for encrypting my UDP traffic. In order to save expensive data quota and reduce battery drain, I have to make use of session resumption, so that I...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
